Lincoln Electric SVM103-A Table D.2 Engine Maintenance Parts, GENERATOR/WELDER Maintenance

Page 35

Return to Section TOC

Return to Master TOC

D-4

MAINTENANCE

TABLE D.2 – ENGINE MAINTENANCE PARTS

Part	Part Number
OIL FILTER	NONE
SPARK PLUG (STANDARD)	B&S 492167
	CHAMPION J19LM
SPARK PLUG (RESISTOR)	B&S 802592
	CHAMPION RJ19LM
FUEL FILTER	B&S 298090 (for .25î I.D. hose)
AIR CLEANER CARTRIDGE	B&S 393957
	(CAN BE CLEANED AND REUSED)
AIR PRE-CLEANER	B&S 271794
(AS NEEDED)	(CAN BE CLEANED AND REUSED)

Return to Section TOC

Section TOC

Return to Master TOC

Master TOC

GENERATOR/WELDER MAINTENANCE

STORAGE: Store the POWER-ARC 4000 in clean, dry, protected areas.

CLEANING: Blow out the generator and controls periodically with low pressure air. Do this at least once a week in particularly dirty areas.

BRUSH REMOVAL AND REPLACEMENT: See Figure D.5. It’s normal for the brushes and slip rings to wear and darken slightly. Inspect the brushes when a generator overhaul is necessary. Remove the brushes and clean the slip rings with fine grit sandpaper. To reinstall the brushes, press them upward and slide a cable tie or wooden stick

through the brush holder tabs. Install the brush holder into the bearing end bracket and secure with the screws previously removed. Remove the cable tie or wooden stick and the brushes will seat onto the slip rings.

RECEPTACLES: Keep the electrical receptacles in good condition. Remove any dirt, oil, or other debris from their surfaces and holes.

CABLE CONNECTIONS: Check the welding cable connections at the weld output terminals often. Be sure that the connections are always firm.

Return to

Return to Section TOC

Return to

Return to Master TOC

FIGURE D.5. – BRUSH REMOVAL AND REPLACEMENT

4	2	6
3		5
3
	1

1.GENERATOR END BRACKET

2.BRUSH HOLDER ASSEMBLY

3.COVER

4.SCREWS (2)

5.BRUSHES

6.CABLE TIE

POWER-ARC 4000

Image 35

Contents POWER-ARC TM4000 POWER-ARC SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionPrécautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications POWER-ARC InstallationStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Cable Size and Length Power ARCElectrical Output Connections Welding Cable ConnectionsPlugs and HAND-HELD Equipment Auxiliary Power ReceptaclesCable Installation Machine GroundingCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCTable of Contents Operation Section General Description Safety InstructionsOperation Operating InstructionsWelding Capability Operational Features and ControlsDesign Features Advantages Recommended ApplicationsGENERATOR/WELDER Controls Controls and SettingsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine BREAK-IN Period Stopping the EngineRunning the Engine General Information To USE the Generator AS AN Auxiliary Power SupplyGenerator Operation Table B.3 Generator Power Applications After YOU Finish the Weld To USE the POWER-ARC 4000 for WeldingWelding Operation Stick Welding Material Thickness Electrode Type Size SettingWelding Guidelines ARC Welding CircuitCorrect WAY to Strike AN ARC 12/95 POWER-ARCFour Factors of Successful Welding ElectrodeCorrect Welding Speed Correct ARC LengthTable of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Engine Maintenance Routine and Periodic MaintenanceFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Figure D.4 SET Spark Plug GAP Part Part Number Table D.2 Engine Maintenance PartsGENERATOR/WELDER Maintenance Figure D.6. Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Theory of OperationFigure E.3 Field Excitation and Auxiliary Power Rotor Field Feedback and Auxiliary PowerWeld Winding and Reactor Auxiliary Power Overcurrent ProtectionTable of Contents Trouble Shooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & RepairOutput Problems Troubleshooting GuideOr contact your local Lincoln Local Lincoln Electric Authorized Troubleshooting & Repair Troubleshooting & Repair Engine Problems Engine Problems Welding Problems Materials Needed Rotor Voltage TestTest Description Ground Stud Lead 200A Connection Output Panel Test ProcedureRotor Resistance Test Rings SlipCable TIE Brushes Figure F.3 Brushes Retained with Cable TIEEngine Throttle Adjustment Test Oscilloscope Method MarkStrobe-tach Method Frequency Counter MethodNUT Figure F.5 Location of Engine Throttle Adjustment NUTHigh Idle no Load Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 23 VAC Typical Weld Output WaveformMachine Loaded Description Brush Removal and ReplacementFigure F.6 Brushes Retained with Cable TIE ProcedureProcedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal Capacitor AND/OR Diode Bridge Removal Replacement Procedure Capacitor Removal and Replacement Capacitor AND/OR Diode Bridge Removal and ReplacementProcedure Diode Bridge Removal and Replacement Instructions STATOR/ROTOR Removal and ReplacementTerminals Stator Removal ProcedureTIE Wrap OutputFigure F.10 Stator END Bracket Support and THRU-BOLTS Thru Bolts Support Nuts POWER-ARCRotor THRU-BOLT Rotor Removal ProcedureReassembly Procedure Rotor Feeler GaugeWELDER/GENERATOR OUTPUT1 Auxiliary Power Receptacle OUTPUT1Retest After Repair Engine OutputPOWER-ARC Section G Table of ContentsElectrical Diagrams POWER-ARC Electrical DiagramPOWER-ARC POWER-ARC