Lincoln Electric SVM103-A service manual Capacitor AND/OR Diode Bridge Removal Replacement

Page 67

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-26

TROUBLESHOOTING & REPAIR

CAPACITOR AND/OR DIODE BRIDGE REMOVAL AND

REPLACEMENT

WARNING

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty. For your safety and to avoid elec- trical shock, please observe all safety notes and precautions detailed throughout this manu- al.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department for electrical trou- bleshooting assistance before you proceed. Call 216-383-2531 or 1-800—833-9353 (WELD).

DESCRIPTION

The following procedure will aid the technician in accessing and removing the capacitor and diode bridge for maintenance or replacement of either component.

MATERIALS NEEDED

5/16” Nut driver

Jumper wire with alligator clips on each end for discharging the field capacitor Slot head screw driver

Needle nose pliers Wiring Diagram

POWER-ARC 4000

Image 67

Contents POWER-ARC TM4000 POWER-ARC SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionPrécautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications POWER-ARC InstallationLocation and Ventilation Safety PrecautionsStoring PRE-OPERATION Engine Service Cable Size and Length Power ARCElectrical Output Connections Welding Cable ConnectionsPlugs and HAND-HELD Equipment Auxiliary Power ReceptaclesCable Installation Machine GroundingCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCTable of Contents Operation Section General Description Safety InstructionsOperation Operating InstructionsWelding Capability Operational Features and ControlsDesign Features Advantages Recommended ApplicationsGENERATOR/WELDER Controls Controls and SettingsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsBefore Starting the Engine Engine OperationStarting the Engine Running the Engine Stopping the EngineBREAK-IN Period Generator Operation To USE the Generator AS AN Auxiliary Power SupplyGeneral Information Table B.3 Generator Power Applications Welding Operation To USE the POWER-ARC 4000 for WeldingAfter YOU Finish the Weld Welding Guidelines Material Thickness Electrode Type Size SettingStick Welding ARC Welding CircuitCorrect WAY to Strike AN ARC 12/95 POWER-ARCFour Factors of Successful Welding ElectrodeCorrect Welding Speed Correct ARC LengthTable of Contents Accessories Lincoln Electric Accessories OPTIONS/ACCESSORIESBriggs and Stratton Accessories Table of Contents Maintenance Engine Maintenance Routine and Periodic MaintenanceFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Figure D.4 SET Spark Plug GAP GENERATOR/WELDER Maintenance Table D.2 Engine Maintenance PartsPart Part Number Figure D.6. Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Theory of OperationFigure E.3 Field Excitation and Auxiliary Power Rotor Field Feedback and Auxiliary PowerWeld Winding and Reactor Auxiliary Power Overcurrent ProtectionTable of Contents Trouble Shooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & RepairOutput Problems Troubleshooting GuideOr contact your local Lincoln Local Lincoln Electric Authorized Troubleshooting & Repair Troubleshooting & Repair Engine Problems Engine Problems Welding Problems Test Description Rotor Voltage TestMaterials Needed Ground Stud Lead 200A Connection Output Panel Test ProcedureRotor Resistance Test Rings SlipCable TIE Brushes Figure F.3 Brushes Retained with Cable TIEEngine Throttle Adjustment Test Oscilloscope Method MarkStrobe-tach Method Frequency Counter MethodNUT Figure F.5 Location of Engine Throttle Adjustment NUTNormal Open Circuit Weld Voltage Waveform Scope SettingsHigh Idle no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded Typical Weld Output WaveformMachine Loaded to 125 Amps AT 23 VAC Description Brush Removal and ReplacementFigure F.6 Brushes Retained with Cable TIE ProcedureProcedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal Capacitor AND/OR Diode Bridge Removal Replacement Procedure Capacitor Removal and Replacement Capacitor AND/OR Diode Bridge Removal and ReplacementProcedure Diode Bridge Removal and Replacement Instructions STATOR/ROTOR Removal and ReplacementTerminals Stator Removal ProcedureTIE Wrap OutputFigure F.10 Stator END Bracket Support and THRU-BOLTS Thru Bolts Support Nuts POWER-ARCReassembly Procedure Rotor Removal ProcedureRotor THRU-BOLT Rotor Feeler GaugeWELDER/GENERATOR OUTPUT1 Auxiliary Power Receptacle OUTPUT1Retest After Repair Engine OutputPOWER-ARC Electrical Diagrams Table of ContentsSection G POWER-ARC Electrical DiagramPOWER-ARC POWER-ARC