Lincoln Electric SVM103-A service manual Feeler Gauge, Rotor

Page 74

TOC

TOC

F-33

TROUBLESHOOTING & REPAIR

STATOR/ROTOR REMOVAL AND REPLACEMENT (continued)

Return to Section

Return to Section TOC

Section TOC

Return to Master

Return to Master TOC

Master TOC

6.Install the bottom two end bracket thru- bolts.

Note: The flat washer goes on the top right hand thru-bolt for the green ground wire.

7.Tap the end bracket with the mallet as necessary to position it. Tighten the bolts to 22 - 25 ft lbs. Alternate tightening in order to pull the assembly together even- ly. As you tighten, look through the brush housing access door and watch the bear- ing to judge end bracket movement and alignment.

8.Check the rotor-stator air gap with the long .010 feeler gauge. The measurement is taken through the brush holder access door; see Figure F12. Turn the engine with the recoil starter rope slightly so that the rotor “iron” is up to take the measure- ment. (The rotor has two flat sides, which are not measured for air gap.) Slide in the gauge. Then rotate the shaft 180 degrees and measure again. If the gauge does not clear, loosen the four end bracket thru- bolts, reposition the end bracket, retight- en the bolts, and recheck the air gap. Repeat until the proper .010 minimum air gap is achieved.

9.Tighten the end bracket support nuts and lock washers. Remove the 2 X 4 engine support.

10.Reinstall the brush holder assembly. Refer to the topic “BRUSH REMOVAL AND REPLACEMENT” in this section of the manual.

11.Slide the control box back into place. Pull the stator and ground wire up through.

12.Remove the control panel (2 screws) and reconnect the output terminal leads (W1, W2). Install a new cable tie to hold the leads together. Reconnect the stator wire/harness molex coupling. Install the 6 screws that hold the control panel to the box.

13.Connect the engine flywheel alternator coupling.

14.Lift the control box and screw in the rub- ber mountings. Set the control box onto the mountings.

15.Install the front left hand washer and nut that anchors the control box to the stator frame. Position the reactor and install the remaining washers and nuts.

16.Check all terminal connections for clear- ance, grounding, and tightness.

17.Replace the top cover to the control box and tighten the 4 nuts.

18.Conduct the “RETEST AFTER REPAIR” procedure, the following topic in this sec- tion of the manual.

Return to

Return to Section TOC

Return to

Return to Master TOC

FIGURE F.12 - CHECKING ROTOR-STATOR AIR GAP

FEELER GAUGE

STATOR

ROTOR

POWER-ARC 4000

Page 73 Page 75
Image 74
Page 73 Page 75
Contents POWER-ARC TM4000 Safety POWER-ARCElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications POWER-ARCStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Welding Cable Connections Power ARCElectrical Output Connections Cable Size and LengthMachine Grounding Auxiliary Power ReceptaclesCable Installation Plugs and HAND-HELD EquipmentPremises Wiring Circuit BreakersTable A.2 Electrical Device USE with the POWER-ARC Type Common Electrical Devices Possible ConcernsTable of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features Advantages Welding CapabilityControls and Settings GENERATOR/WELDER ControlsFigure B.2 Gasoline Engine Controls Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine BREAK-IN Period Stopping the EngineRunning the Engine General Information To USE the Generator AS AN Auxiliary Power SupplyGenerator Operation Table B.3 Generator Power Applications After YOU Finish the Weld To USE the POWER-ARC 4000 for WeldingWelding Operation Stick Welding Material Thickness Electrode Type Size SettingWelding Guidelines Welding Circuit ARCElectrode 12/95 POWER-ARCFour Factors of Successful Welding Correct WAY to Strike AN ARCCorrect ARC Length Correct Welding SpeedTable of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Figure D.4 SET Spark Plug GAP Part Part Number Table D.2 Engine Maintenance PartsGENERATOR/WELDER Maintenance Figure D.6. Major Component Locations Table of Contents Theory of Operation Section Theory of Operation ENGINE, EXCITATION, Rotor and StatorRotor Field Feedback and Auxiliary Power Figure E.3 Field Excitation and Auxiliary PowerAuxiliary Power Overcurrent Protection Weld Winding and ReactorTable of Contents Trouble Shooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuideTroubleshooting Guide Output ProblemsOr contact your local Lincoln Local Lincoln Electric Authorized Troubleshooting & Repair Troubleshooting & Repair Engine Problems Engine Problems Welding Problems Materials Needed Rotor Voltage TestTest Description Test Procedure Ground Stud Lead 200A Connection Output PanelRotor Resistance Test Slip RingsFigure F.3 Brushes Retained with Cable TIE Cable TIE BrushesEngine Throttle Adjustment Test Frequency Counter Method MarkStrobe-tach Method Oscilloscope MethodFigure F.5 Location of Engine Throttle Adjustment NUT NUTHigh Idle no Load Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 23 VAC Typical Weld Output WaveformMachine Loaded Brush Removal and Replacement DescriptionProcedure Figure F.6 Brushes Retained with Cable TIEProcedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal Capacitor AND/OR Diode Bridge Removal Replacement Capacitor AND/OR Diode Bridge Removal and Replacement Procedure Capacitor Removal and ReplacementProcedure Diode Bridge Removal and Replacement STATOR/ROTOR Removal and Replacement InstructionsOutput Stator Removal ProcedureTIE Wrap TerminalsThru Bolts Support Nuts POWER-ARC Figure F.10 Stator END Bracket Support and THRU-BOLTSRotor THRU-BOLT Rotor Removal ProcedureReassembly Procedure Feeler Gauge RotorEngine Output Auxiliary Power Receptacle OUTPUT1Retest After Repair WELDER/GENERATOR OUTPUT1POWER-ARC Section G Table of ContentsElectrical Diagrams Electrical Diagram POWER-ARCPOWER-ARC POWER-ARC
Top Page Image Contents