Lincoln Electric SVM103-A service manual Rotor Resistance Test

Page 53

to Section TOC

to Master TOC

TROUBLESHOOTING & REPAIR

ROTOR RESISTANCE TEST

WARNING

F-12

Return

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return

Return to Master TOC

Return to Master TOC

Return to Master TOC

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty. For your safety and to avoid elec- trical shock, please observe all safety notes and precautions detailed throughout this manu- al.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department for electrical trou- bleshooting assistance before you proceed. Call 216-383-2531 or 1-800—833-9353 (WELD).

TEST DESCRIPTION

This test will determine if there is a shorted winding in the rotor or if the rotor is grounded.

MATERIALS NEEDED

Volt/Ohmmeter 1/4” Nut driver

Small slot head screw driver Wiring Diagram

POWER-ARC 4000

Image 53

Contents POWER-ARC TM4000 POWER-ARC SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionPrécautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications POWER-ARC InstallationStoring Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Electrical Output Connections Power ARCWelding Cable Connections Cable Size and LengthCable Installation Auxiliary Power ReceptaclesMachine Grounding Plugs and HAND-HELD EquipmentCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCTable of Contents Operation Section Operation Safety InstructionsOperating Instructions General DescriptionDesign Features Advantages Operational Features and ControlsRecommended Applications Welding CapabilityGENERATOR/WELDER Controls Controls and SettingsGasoline Engine Controls Figure B.2 Gasoline Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine BREAK-IN Period Stopping the EngineRunning the Engine General Information To USE the Generator AS AN Auxiliary Power SupplyGenerator Operation Table B.3 Generator Power Applications After YOU Finish the Weld To USE the POWER-ARC 4000 for WeldingWelding Operation Stick Welding Material Thickness Electrode Type Size SettingWelding Guidelines ARC Welding CircuitFour Factors of Successful Welding 12/95 POWER-ARCElectrode Correct WAY to Strike AN ARCCorrect Welding Speed Correct ARC LengthTable of Contents Accessories Briggs and Stratton Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Engine Maintenance Routine and Periodic MaintenanceFigure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Figure D.4 SET Spark Plug GAP Part Part Number Table D.2 Engine Maintenance PartsGENERATOR/WELDER Maintenance Figure D.6. Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Theory of OperationFigure E.3 Field Excitation and Auxiliary Power Rotor Field Feedback and Auxiliary PowerWeld Winding and Reactor Auxiliary Power Overcurrent ProtectionTable of Contents Trouble Shooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & RepairOutput Problems Troubleshooting GuideOr contact your local Lincoln Local Lincoln Electric Authorized Troubleshooting & Repair Troubleshooting & Repair Engine Problems Engine Problems Welding Problems Materials Needed Rotor Voltage TestTest Description Ground Stud Lead 200A Connection Output Panel Test ProcedureRotor Resistance Test Rings SlipCable TIE Brushes Figure F.3 Brushes Retained with Cable TIEEngine Throttle Adjustment Test Strobe-tach Method MarkFrequency Counter Method Oscilloscope MethodNUT Figure F.5 Location of Engine Throttle Adjustment NUTHigh Idle no Load Scope SettingsNormal Open Circuit Weld Voltage Waveform Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded to 125 Amps AT 23 VAC Typical Weld Output WaveformMachine Loaded Description Brush Removal and ReplacementFigure F.6 Brushes Retained with Cable TIE ProcedureProcedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal Capacitor AND/OR Diode Bridge Removal Replacement Procedure Capacitor Removal and Replacement Capacitor AND/OR Diode Bridge Removal and ReplacementProcedure Diode Bridge Removal and Replacement Instructions STATOR/ROTOR Removal and ReplacementTIE Wrap Stator Removal ProcedureOutput TerminalsFigure F.10 Stator END Bracket Support and THRU-BOLTS Thru Bolts Support Nuts POWER-ARCRotor THRU-BOLT Rotor Removal ProcedureReassembly Procedure Rotor Feeler GaugeRetest After Repair Auxiliary Power Receptacle OUTPUT1Engine Output WELDER/GENERATOR OUTPUT1POWER-ARC Section G Table of ContentsElectrical Diagrams POWER-ARC Electrical DiagramPOWER-ARC POWER-ARC