Scag Power Equipment SFZ36-20BS, SFZ61-28BS, SFZ36-17KA Safety and Instructional Decals, 483633

Page 12

R

Section 2

2.8 SAFETY AND INSTRUCTIONAL DECALS

483405

483505

483402

 

481568

483406

483633

Failure to follow these instructions could result in serious injury or death.

DO NOT operate machine on steep slopes or near drop offs.

Avoid sharp and/or quick turns.

DO NOT exceed the machine weight rating.

Always use seatbelt. DO NOT jump if machine tips.

DO NOT repair or modify roll bar.

Any alteration of the roll bar will void certification if not approved by manufacturer.

483425

483660

482291

483467

2008 SFZ Safety Decals Rev.1

8

Image 12
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited warranty sfz Following section AdjustmentsGeneral Information IntroductionDirection Reference Servicing The Engine and Drive Train ComponentsSymbols STT ModelsSafety Information Signal WordsThis symbol means Attention! Become Alert! Your Signal WordOperation Considerations Section Roll-over protection system Seat Belt InspectionMaintenance Considerations & storage Using a spark arrestorSafety and Instructional Decals 483633Specifications EngineElectrical TractorWeights and Dimensions 48/52 Cutter DeckHydraulic System ProductivityOperating Instructions Controls and InstrumentIdentification Engine Throttle Control -1. Used toSafety Interlock System Initial RUN-IN ProceduresFirst Day of Use or Approximately 20 Hours Starting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelRotating Blades Hillside OperationAfter Operation Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch Accessory Not available for sfz36 Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Dirt or CuttingVery Close To the GroundStep Cut Ridge in Center Cutting pathAdjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentTracking Adjustment Belt AlignmentCutter Deck Adjustments Cutter Deck PitchCutter Deck Level Cutter Deck Height Adjustment Cutter Deck HeightElectric clutch adjustment Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsProcedure Comments Break-In 100 200 400 First Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Checking Engine Crankcase Oil LevelChanging Engine Crankcase Oil Engine Fuel System Changing Engine Oil FilterFilling the Fuel Tank Battery Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Replacing In-Line Fuel Filter ElementsCharging the Battery Drive BeltsJump Starting Blade Replacement Cutter BladesBlade Inspection Blade SharpeningTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and AccessoriesCutter Deck Cutter Deck DescriptionSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt Fuel and Electrical System SFZ48, SFZ52 & SFZ61 483364 Tank, LHZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 Replacement Decals and Information Plates 36COMMERCIALReplacement Decals and Information Plates Electrical Schematic Optional Black Light RED Accessory HourmeterLimited Warranty SFZ