Scag Power Equipment SFZ36-17KA Cutter Deck, Hydraulic System, Weights and Dimensions 48/52

Page 14

R

Section 3

Travel Speed:
Forward	0-8 MPH
Reverse	0-5 MPH
-NOTE- The machine will travel at 8 mph for transport purposes. For best cutting performance the forward travel
speed should be adjusted depending upon the cutting conditions.

3.4 Cutter Deck

Type	Floating, Adjustable, Anti-Scalping, Hybrid Design Combines Out-Front and Belly-Mount Designs
Construction		10-Gauge top with 11-Gauge reinforcement throughout
		the spindle area, 7-Gauge skirt for strength and longevity
True Cutting Width:
36		36" (91.44 cm)
48		48" (122.0 cm)
52		52" (132.0 cm)
61		61" (154.94 cm)
Cutting Height Adjustment		Foot-Operated Lever Adjustment from Operator's Seat, 1.00" to 4.5" in 1/4"increments
Cutter Blades		0.197 in. Thick, Milled Edge, Wear Resistant Marbain™
Blade Engagement		Electric Blade Engagement Clutch with Control Panel Switch
		Connected to the Cutter Deck through a Belt.
Discharge Opening		Extra Wide Discharge Opening with Spring-Loaded Discharge Chute
Discharge Chute		Black, Polypropylene (Plastic), Flexible
Spindles	Heavy-Duty Spindle Shaft, Cast Aluminum Housing, Sealed Ball Bearing, Maintenance-Free
Spindle Pulleys		Split Steel
Cutter Deck Belts		B-section with Kevlar Cord. Self-Adjusting, Self-Tightening
Electric Clutch Type		Ogura Heavy Duty PTO Clutch Brake

3.5 Hydraulic System

Hydraulic Oil Filter	40 Micron Spin-on Element Type
Hydraulic Expansion Reservoir	Nylon

3.6 Weights and Dimensions	36	48/52	61
Length	73"	73"	79"
Tracking Width	35.5"	47.5"	47.5"
Overall Width w/chute down	48.5"	60.5" / 64.5"	73.5"
Overall Width w/chute up	37"	49" / 53"	62"
Overall Height	60"	60"	60"
Operating Weight	690#	775# / 785#	810#

PRODUCTIVITY	36	48/52	61
Cutting Width	36"	48"/52"	61"
Acres Per Day	14	18.6/20.2	23.7

The preceding chart will aid you in determining how many acres your Scag mower will cut per day. The chart is an estimate based on 8 hours per day cutting time at 6 MPH with a 20% allowance for overlap and turns.

10

Image 14

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited warranty sfz Following section AdjustmentsDirection Reference General InformationIntroduction Servicing The Engine and Drive Train ComponentsSymbols STT ModelsThis symbol means Attention! Become Alert! Your Safety InformationSignal Words Signal WordOperation Considerations Section Roll-over protection system Seat Belt InspectionMaintenance Considerations & storage Using a spark arrestorSafety and Instructional Decals 483633Electrical SpecificationsEngine TractorHydraulic System Weights and Dimensions 48/52Cutter Deck ProductivityIdentification Operating InstructionsControls and Instrument Engine Throttle Control -1. Used toFirst Day of Use or Approximately 20 Hours Safety Interlock SystemInitial RUN-IN Procedures Forward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Rotating BladesHillside Operation Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Towing optional hitch Accessory Not available for sfz36 Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Step Cut Ridge in Center Scalping Blades HittingDirt or CuttingVery Close To the Ground Cutting pathAdjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Adjustment Cutter Deck HeightElectric clutch adjustment Clutch Air Gap AdjustmentProcedure Comments Break-In 100 200 400 First MaintenanceMaintenance Chart Recommended Service Intervals Checking Hydraulic Oil Level Changing Hydraulic OilChanging Engine Crankcase Oil Engine OilChecking Engine Crankcase Oil Level Filling the Fuel Tank Engine Fuel SystemChanging Engine Oil Filter Cleaning and/or Replacing Air Cleaner Element BatteryEngine Air Cleaner Replacing In-Line Fuel Filter ElementsJump Starting Charging the BatteryDrive Belts Blade Inspection Blade ReplacementCutter Blades Blade SharpeningTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and AccessoriesCutter Deck Cutter Deck DescriptionSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt Fuel and Electrical System SFZ48, SFZ52 & SFZ61 483364 Tank, LHZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 Replacement Decals and Information Plates 36COMMERCIALReplacement Decals and Information Plates Electrical Schematic Optional Black Light RED Accessory HourmeterLimited Warranty SFZ