Scag Power Equipment SFZ36-17KA Starting the Engine, Ground Travel and Steering, Forward Travel

Page 17

Section 4

R

5.Check interlock system for proper operation. (See Section 4.2.)

6.Check tire pressure. Adjust pressure if necessary. (See Section 7.10.)

4.4 STARTING THE ENGINE

Start practicing with a slow engine speed and slow forward travel.

Learn to feather the steering controls to obtain a smooth operating action.

Practice operating the mower until you are comfortable with the controls before proceeding to mow.

CAUTION

DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.

1.Be sure the fuel shutoff valve, located behind the operator's seat, is completely open.

2.Sit in the operator’s seat, fasten seat belt and place the steering control levers in the neutral position.

3.Engage the parking brake.

4.Place the PTO switch in the disengaged position.

5.If the engine is cold, choke the engine as needed.

6.Move the engine throttle control to about half engine speed.

7.Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.

8.Allow engine to warm before operating the mower.

4.5 GROUND TRAVEL AND STEERING

- IMPORTANT -

If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions.

Learn the operation on flat ground before operating on slopes.

Forward Travel

To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back.The further the lever is pulled back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

- NOTE -

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

- IMPORTANT -

Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (See Figure 4-1 item 12 for cutter deck raising description.)

13

Image 17
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Adjustments Limited warranty sfz Following sectionIntroduction General InformationDirection Reference Servicing The Engine and Drive Train ComponentsSTT Models SymbolsSignal Words Safety InformationThis symbol means Attention! Become Alert! Your Signal WordOperation Considerations Section Seat Belt Inspection Roll-over protection systemUsing a spark arrestor Maintenance Considerations & storage483633 Safety and Instructional DecalsEngine SpecificationsElectrical TractorCutter Deck Weights and Dimensions 48/52Hydraulic System ProductivityControls and Instrument Operating InstructionsIdentification Engine Throttle Control -1. Used toFirst Day of Use or Approximately 20 Hours Safety Interlock SystemInitial RUN-IN Procedures Forward Travel Starting the EngineGround Travel and Steering Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Rotating BladesAfter Operation Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Towing optional hitch Accessory Not available for sfz36 Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Dirt or CuttingVery Close To the Ground Scalping Blades HittingStep Cut Ridge in Center Cutting pathParking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Adjustment Throttle Control and Choke AdjustmentsTracking Adjustment Belt AlignmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Cutter Deck Height AdjustmentClutch Air Gap Adjustment Electric clutch adjustmentProcedure Comments Break-In 100 200 400 First MaintenanceMaintenance Chart Recommended Service Intervals Changing Hydraulic Oil Checking Hydraulic Oil LevelChanging Engine Crankcase Oil Engine OilChecking Engine Crankcase Oil Level Filling the Fuel Tank Engine Fuel SystemChanging Engine Oil Filter Engine Air Cleaner BatteryCleaning and/or Replacing Air Cleaner Element Replacing In-Line Fuel Filter ElementsJump Starting Charging the BatteryDrive Belts Cutter Blades Blade ReplacementBlade Inspection Blade SharpeningBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts ListCutter Deck Description Cutter DeckSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt 483364 Tank, LH Fuel and Electrical System SFZ48, SFZ52 & SFZ61ZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 36COMMERCIAL Replacement Decals and Information PlatesReplacement Decals and Information Plates Optional Black Light RED Accessory Hourmeter Electrical SchematicLimited Warranty SFZ