Scag Power Equipment SFZ36-20BS, SFZ61-28BS, SFZ36-17KA operating instructions Symbols, STT Models

Page 6

R

Section 1

1.4 Symbols
SYMBOL	DESCRIPTION	SYMBOL	DESCRIPTION
	Choke		Transmission
	Parking Brake		Spinning Blade
		48071S
	On/Start		Spring Tension on Idler
	Off/Stop		Oil
	Falling Hazard		Thrown Object Hazard
	Fast		Slow
	Continuously Variable - Linear		Cutting Element - Basic Symbol
	Pinch Point		Cutting Element - Engage
481039S
	Hour meter/Elapsed Operating Hours		Cutting Element - Disengage
	STT Models		CE Mark

Seat must be installed under the seat hold down bracket during installation. Failure to secure the seat under the hold down bracket could result in serious injury or death in a roll over.

Thrown Object Hazard		Read Operator's Manual
Thrown Object Hazard		Read Operator's Manual
Keep Bystanders Away

2

Image 6

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited warranty sfz Following section AdjustmentsDirection Reference General InformationIntroduction Servicing The Engine and Drive Train ComponentsSymbols STT ModelsThis symbol means Attention! Become Alert! Your Safety InformationSignal Words Signal WordOperation Considerations Section Roll-over protection system Seat Belt InspectionMaintenance Considerations & storage Using a spark arrestorSafety and Instructional Decals 483633Electrical SpecificationsEngine TractorHydraulic System Weights and Dimensions 48/52Cutter Deck ProductivityIdentification Operating InstructionsControls and Instrument Engine Throttle Control -1. Used toSafety Interlock System Initial RUN-IN ProceduresFirst Day of Use or Approximately 20 Hours Starting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Rotating BladesHillside Operation Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch Accessory Not available for sfz36 Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Step Cut Ridge in Center Scalping Blades HittingDirt or CuttingVery Close To the Ground Cutting pathAdjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Adjustments Cutter Deck PitchCutter Deck Level Cutter Deck Height Adjustment Cutter Deck HeightElectric clutch adjustment Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsProcedure Comments Break-In 100 200 400 First Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Checking Engine Crankcase Oil LevelChanging Engine Crankcase Oil Engine Fuel System Changing Engine Oil FilterFilling the Fuel Tank Cleaning and/or Replacing Air Cleaner Element BatteryEngine Air Cleaner Replacing In-Line Fuel Filter ElementsCharging the Battery Drive BeltsJump Starting Blade Inspection Blade ReplacementCutter Blades Blade SharpeningTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and AccessoriesCutter Deck Cutter Deck DescriptionSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt Fuel and Electrical System SFZ48, SFZ52 & SFZ61 483364 Tank, LHZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 Replacement Decals and Information Plates 36COMMERCIALReplacement Decals and Information Plates Electrical Schematic Optional Black Light RED Accessory HourmeterLimited Warranty SFZ