Scag Power Equipment SFZ36-20BS, SFZ61-28BS, SFZ36-17KA operating instructions Section

Page 9

Section 2

R

3.To prevent tipping or loss of control, start and stop smoothly, avoid unnecessary turns and travel at reduced speed. Use caution when operating the mower on an incline with the optional grass catcher installed.

15.The machine and attachments should be stopped and inspected for damage after striking a foreign object, and damage should be repaired before restarting and operating the machine.

4.When using any attachment, never direct the discharge of material toward bystanders or allow anyone near the machine while in operation.

5.Before attempting to start the engine, with the operator in the seat, disengage power to the cutter deck, place the steering control levers in the neutral position and engage the parking brake.

6.If the mower discharge ever plugs, shut off the engine, remove the ignition key, and wait for all movement to stop before removing the obstruction.

WARNING

DO NOT use your hand to dislodge the clogged discharge chute. Use a stick or other device to remove clogged material after the engine has stopped running and the blades have stopped turning.

7.Be alert for holes, rocks, roots and other hidden hazards in the terrain. Keep away from any drop- offs. Beware of overhead obstructions (low limbs, etc.), underground obstacles (sprinklers, pipes, tree roots, etc.). Cautiously enter a new area. Be alert for hidden hazards.

8.Disengage power to cutter deck before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower. If you must mow in reverse, maintain a constant lookout to the rear of the machine and mow slowly.

9.DO NOT turn sharply. Use care when backing up.

10.Disengage power to cutter deck before crossing roads, walks or gravel drives.

11.Mow only in daylight or good artificial light.

12.NEVER raise the deck with the blades engaged.

13.Take all possible precautions when leaving the machine unattended, such as disengaging the mower, lowering the attachments, setting the parking brake, stopping the engine, and removing the key.

14.Disengage power to the attachments when transporting or when not in use.

5

Caution

Do not touch the engine or the muffler while the engine is running or immediately after stopping. These areas may be hot enough to cause a burn.

DANGER

DO NOT run the engine inside a building or a confined area without proper ventilation. Exhaust fumes are hazardous and contain carbon monoxide which can cause brain injury and death.

16.Keep hands and feet away from cutter blades and moving parts. Contact can injure.

17.Transport the mower using a heavy duty trailer or truck. Insure the trailer or truck has all of the necessary lighting and markings as required by laws, codes, and ordinances. Secure a trailer with a safety chain.

18.Be cautious when loading and unloading onto trailers or trucks. Use only a full width ramp. Ramp angle should be no more than 15 degrees. Back up the ramp and drive down forward.

19.When transporting the mower, make sure the park brake is engaged, the steering control levers are in the neutral position, the engine is off with the key removed, and the wheels have been blocked.

20.Tie the mower down securely using straps, chains, cable, or ropes. Both front and rear straps must be directed down and outward from machine.

21.Use care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

22.NEVER leave the machine running unattended.

Image 9
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Adjustments Limited warranty sfz Following sectionIntroduction General InformationDirection Reference Servicing The Engine and Drive Train ComponentsSTT Models SymbolsSignal Words Safety InformationThis symbol means Attention! Become Alert! Your Signal WordOperation Considerations Section Seat Belt Inspection Roll-over protection systemUsing a spark arrestor Maintenance Considerations & storage483633 Safety and Instructional DecalsEngine SpecificationsElectrical TractorCutter Deck Weights and Dimensions 48/52Hydraulic System ProductivityControls and Instrument Operating InstructionsIdentification Engine Throttle Control -1. Used toSafety Interlock System Initial RUN-IN ProceduresFirst Day of Use or Approximately 20 Hours Starting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Rotating BladesAfter Operation Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch Accessory Not available for sfz36 Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Dirt or CuttingVery Close To the Ground Scalping Blades HittingStep Cut Ridge in Center Cutting pathParking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Adjustment Throttle Control and Choke AdjustmentsTracking Adjustment Belt AlignmentCutter Deck Adjustments Cutter Deck PitchCutter Deck Level Cutter Deck Height Cutter Deck Height AdjustmentClutch Air Gap Adjustment Electric clutch adjustmentMaintenance Maintenance Chart Recommended Service IntervalsProcedure Comments Break-In 100 200 400 First Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Oil Checking Engine Crankcase Oil LevelChanging Engine Crankcase Oil Engine Fuel System Changing Engine Oil FilterFilling the Fuel Tank Engine Air Cleaner BatteryCleaning and/or Replacing Air Cleaner Element Replacing In-Line Fuel Filter ElementsCharging the Battery Drive BeltsJump Starting Cutter Blades Blade ReplacementBlade Inspection Blade SharpeningBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts ListCutter Deck Description Cutter DeckSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt 483364 Tank, LH Fuel and Electrical System SFZ48, SFZ52 & SFZ61ZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 36COMMERCIAL Replacement Decals and Information PlatesReplacement Decals and Information Plates Optional Black Light RED Accessory Hourmeter Electrical SchematicLimited Warranty SFZ