Scag Power Equipment SFZ36-17KA, SFZ36-20BS, SFZ61-28BS Battery, Engine Air Cleaner

Page 35

Section 7

R

9.If fuel is spilled on clothing, change clothing immediately and wash affected skin.

10.Replace gas cap and tighten securely.

- NOTE -

In extremely dusty conditions it may be necessary to check the element once or twice daily to prevent engine damage.

B. Replacing In-Line Fuel Filter Elements

The engine fuel filter should be replaced after every 400 hours of operation or annually, whichever occurs first. See Figure 7-7.

1.Close the shut-off valve.

2.Remove and replace the engine fuel filter. Open the fuel shut-off valve.

ENGINE OIL FILTER

1.Loosen the two bolts securing the air cleaner cover to the air cleaner assembly and remove the cover. Set aside.

2.Remove the air cleaner and inspect.

3.Clean or replace the air cleaner and foam pre-cleaner as recommended by the engine manufacturer.

4.Replace the air cleaner cover and secure.

7.6 Battery

2007 SFZ EOFF

ENGINE FUEL

FILTER

WARNING

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

WARNING

Figure 7-7. Fuel Filter

7.5 Engine Air Cleaner

A. Cleaning and/or Replacing Air Cleaner Element

For any air cleaner, the operating environment dictates the air cleaner service periods. Inspect and clean the air cleaner element after every 100 hours of operation or bi- weekly, whichever occurs first and replace the element if required.

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. Wash hands after handling.

31

Image 35
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Adjustments Limited warranty sfz Following sectionServicing The Engine and Drive Train Components General InformationIntroduction Direction ReferenceSTT Models SymbolsSignal Word Safety InformationSignal Words This symbol means Attention! Become Alert! YourOperation Considerations Section Seat Belt Inspection Roll-over protection systemUsing a spark arrestor Maintenance Considerations & storage483633 Safety and Instructional DecalsTractor SpecificationsEngine ElectricalProductivity Weights and Dimensions 48/52Cutter Deck Hydraulic SystemEngine Throttle Control -1. Used to Operating InstructionsControls and Instrument IdentificationFirst Day of Use or Approximately 20 Hours Safety Interlock SystemInitial RUN-IN Procedures Forward Travel Starting the EngineGround Travel and Steering Reverse Travel Engaging the Deck Drive Cutter BladesRemoving Clogged Material Rotating BladesHillside Operation After OperationRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Towing optional hitch Accessory Not available for sfz36 Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Cutting path Scalping Blades HittingDirt or CuttingVery Close To the Ground Step Cut Ridge in CenterParking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Tracking AdjustmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Cutter Deck Height AdjustmentClutch Air Gap Adjustment Electric clutch adjustmentProcedure Comments Break-In 100 200 400 First MaintenanceMaintenance Chart Recommended Service Intervals Changing Hydraulic Oil Checking Hydraulic Oil LevelChanging Engine Crankcase Oil Engine OilChecking Engine Crankcase Oil Level Filling the Fuel Tank Engine Fuel SystemChanging Engine Oil Filter Replacing In-Line Fuel Filter Elements BatteryEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementJump Starting Charging the BatteryDrive Belts Blade Sharpening Blade ReplacementCutter Blades Blade InspectionBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts ListCutter Deck Description Cutter DeckSection 48, 52 & 61 Cutter Decks Flatwasher, 3/8-.391 x .938 x Cutter Deck Controls SFZ36 Ref. No Description Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ48 & SFZ52 Cutter Deck Controls SFZ61 Cutter Deck Controls SFZ61 Sheet Metal Components Flatwasher, 1/4-.312 x .750 x SFZ ROLL-OVER Protection System ROPS, SFZ36 Drive System Components SFZ36 Rod, Brake Adjustment Drive System Components SFZ48, SFZ52 & SFZ61 44162 Linkage, Dump Valve Fuel and Electrical System SFZ36 483672 Tank, LH Switch Clutch Engine Mount Bolt 483364 Tank, LH Fuel and Electrical System SFZ48, SFZ52 & SFZ61ZT-3100 Hydraulic Axle Assembly HG51462 ZT-3400 Hydraulic Axle Assembly -SFZ61 ZT-3400 Hydraulic Axle Assembly SFZ61 36COMMERCIAL Replacement Decals and Information PlatesReplacement Decals and Information Plates Optional Black Light RED Accessory Hourmeter Electrical SchematicLimited Warranty SFZ