Remington Power Tools BS188A, BPS188A, BS188A Chain Saw Information, Chain Saw Assembly

Page 11

Chain Saw Information

Chain Saw Assembly

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

1.Align rib on chain saw power head with groove in main handle (see Figure 5).

2.Slide power head into main handle until units “snap” together (see Figure 6). IMPORTANT: Both release buttons on main handle must be fully engaged.

3.Slide battery onto main handle until release buttons “snap” together (see Figure 7).

Note: Fully charge battery before using for first time. See Charging Battery, page 10.

NOTE: Your Remington Cordless Polesaw and Cordless Chainsaw may have been purchased together (as a 2-in-1 polesaw/ chainsaw) or seperate (chainsaw only). If the chainsaw was purchased separately, the pole is available as an accessory and may be purchased by visiting the "On-Line Outlet" at www.desatech.com.

Groove

Rib

Main

Handle

Power Head

Figure 5 - Align Power Head with

Handle

Figure 6 - Assembled Power Head Main Handle

Main Handle

Battery

Figure 7 - Assemble Battery onto Main

Handle

Saw Chain Tension

WARNING: Remove battery from chainsawbeforeadjustingsawchain tension. Severe injury or death could occur from body contact with moving chain.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: Maintain proper chain tension always.Aloose chain will increase the risk of kickback.A loose chain may jump out of guide bar groove. This may injure op- erator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly.

Note: The saw chain tension is properly set at the factory. A new chain will stretch. Check new chain tension frequently (after discon- necting battery) during the first 2 hours of operation. Allow chain to cool down. Follow steps below to check saw chain tension.

1.Remove battery from chain saw.

2.Place chain saw on a firm surface to check chain tension.

3.Pull chain with light force 1/8" away from bottom of guide bar and release (see Figure 8). If chain lightly snaps back into place, tension is correct. A slight sag (1/16" or less) between chain and bottom of guide bar is acceptable.

Figure 8 - Check Chain Tension

Saw Chain Tension Adjustment

1.Loosen guide bar nuts before adjust- ing chain (see Figure 9).

Guide Bar Nuts

Figure 9 - Loosen Guide Bar Nuts

2.Turn adjusting screw on front of power head clockwise until slack is out of chain (see Figure 10).

3.Wearing protective gloves, pull down on chain to check chain tension (See Step 3 Saw Chain Tension).

Adjusting

Screw

Figure 10 - Turning Adjusting Screw

ENGLISH

www.desatech.com

11

ww.desatech.com

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Volt Cordless Chainsaw Stop Introduction ContentsWhile Operating Saw Important Safety InformationBefore Operating Saw Kickback IMPORTANT Safety InformationMaintenance Storage of Saw Storage Polesaw Trimming PrecautionsGeneral Maintenance ServicePoleSaw Product IdentificationChain Saw Bar that reduces chance of kickback Chain SAW terms and definitionsRear Handle Handle located at rear of saw body Reduced Kickback Guide Bar Guide10.0 Rechargeable batteryProtective Battery Terminal Cap Safety WarningsImportant Charging Notes Charging BatteryChain Saw Information Chain Saw AssemblySaw Chain Tension Adjustment Loosen guide bar nuts before adjust- ing chain see FigureBefore Felling a Tree Oiling ChainFelling a Tree Cutting Down a Tree Cutting with the Chain SawCut towards notch Felling Procedure Felling NotchLimbing a Tree Felling CutEntire Length Of Log On Ground Bucking a LogTrimming a Tree Pruning Log Supported On One EndCutting with the Polesaw Polesaw AssemblyAdjusting Pole Length Polesaw InformationSharpening Saw Chain Cleaning and MaintenanceCleaning Saw Body Care of Guide BarPlace sprocket cover onto guide bar bolts Replacing Saw ChainFiling Cutter Depth Gauges Observed Fault Possible Cause Remedy TroubleshootingSee pages 43 through 44 for an Illustrated Parts List Warranty ServiceNon-Warranty Service Box Warranty InformationManual Para EL Usuario Información sobre la sierra de cadena Diagnóstico Y Resolución DE ProblemasIntroducción Entificación del ProductoAl utilizar la sierra Información Importante DE SeguridadAntes DE Utilizar LA Sierra Cómo llevar la sierra ContragolpesAl cortar, no aplique gra fuerza a la sierra Mantenimiento General AlmacenamientoMantenimiento de la cadena y seguridad contra contragolpes Inspeccione la cadena serrada antes y después de cada usoPrecauciones al recortar con la sierra de pértiga DesembalajePoleSaw Cadena Identificación del ProductoTérminos y definiciones de la sierra de cadena Cord AWG Cord Batería recargableTapa protectora del terminal de la batería Advertencias de SeguridadNotas importantes sobre la carga Carga de la bateríaTensión de la sierra de cadena Ensamblado de la sierra de cadenaRealización DE Cortes Ajuste DE Tensión DE LA Cadena SerradaLubricación DE LA Cadena Procedimiento de tala Corte de la muesca Tala DE UN Árbol Derribamiento de un árbolAdvertencia Antes de derribar un árbolTronco apoyado en un extremo Desmembramiento DE UN ÁrbolTrozado DE UN Tronco La totalidad del tronco sobre el sueloFigura 20- Poda de una rama Poda DE UN ÁrbolInformación sobre la sierra de Pértiga Corté CON LA Sierra DE Pértiga Regulación DE LA Longitud DE LA PértigaAfilado DE LA Cadena Limpieza Y MantenimientoLimpieza DEL Cabezal Cuidado DE LA Barra DE GuíaAjuste bien la barra guía con la llave Recambio de la cadena serradaLimado de los calibradores de medida de profundidad Diagnóstico Y Resolución DE Problemas Servicio con garantía Servicio TécnicoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónGarantía Limitada Garantía EstándarGarantía Estándar de la Batería Illustrated Parts LIST/DESGLOSE Ilustrado DE Partes BS188A Parts LIST/LISTA DE RepuestosParts Centrals / Central DE Piesaz 121071-01 REV.A 11/07

BS188A, BPS188A, BS188A, BPS188A, BS188A specifications

Remington Power Tools has established a reputation for manufacturing high-quality equipment that meets the needs of both professional tradespeople and DIY enthusiasts. Among their wide array of tools, the BS188A and BPS188A models stand out as versatile and reliable options for various tasks.

The BS188A is a powerful and efficient tool designed for heavy-duty job applications. It features a robust motor that provides exceptional performance, ensuring that it can handle even the toughest materials with ease. The lightweight design allows for extended usage without causing fatigue, making it suitable for a wide range of tasks, from woodworking to metalworking.

One of the standout features of the BS188A is its variable speed control, which provides users the flexibility to adjust the tool's speed according to the specific requirements of their project. This feature enhances precision and ensures that users can achieve the desired results consistently. Additionally, the tool comes with an ergonomic handle that provides a comfortable grip, reducing strain during operation.

The BPS188A model complements the BS188A by offering added versatility with a broader range of applications. It includes advanced technology such as an automatic feed system that enables users to work more efficiently, minimizing downtime between tasks. This feature streamlines workflows, making it easier to tackle larger projects without interruptions.

Another notable characteristic of the BPS188A is its high-capacity battery, which ensures longer run times and faster charging. This provides an added layer of convenience, as users can work longer hours without worrying about running out of power. Furthermore, the inclusion of LED indicators helps to keep track of battery life, allowing users to recharge when necessary.

Both models also prioritize user safety, incorporating features such as overload protection and a quick-stop function. These safety measures are crucial in preventing accidents and ensuring that users can operate the tools with confidence, regardless of their experience level.

In summary, the Remington Power Tools BS188A and BPS188A models combine performance, versatility, and safety. With their powerful motors, ergonomic designs, and advanced features, these tools are perfect for anyone looking to enhance their productivity and tackle various projects with ease. Whether for professional use or personal projects, these tools deliver reliability and efficiency.
Top Page Image Contents