Remington Power Tools BS188A, BPS188A, BS188A Limbing a Tree, Felling Procedure Felling Notch

Page 13

Chain Saw Information

Felling Procedure

A) Felling Notch

A properly placed felling notch will deter- mine direction tree will fall. Place felling notch on side of tree in direction you want tree to fall (see Figure 15).

Follow directions below to create a felling notch.

1.Make lower notch cut as close to ground as possible. Hold saw so guide bar is horizontal. Cut 1/3 the diameter of tree trunk (see Figure 15). Note: Always make this horizontal lower notch cut first. If you make this cut second, tree can pinch chain or guide bar.

2.Start upper notch cut the same distance above first cut as first cut is deep.

Example: If lower notch cut is eight inches deep, start upper notch cut eight inches above it. Cut downward at 45° angle. The upper notch cut should meet end of lower notch cut (see Figure 15).

3.Remove tree trunk wedge created by notching cuts.

 

 

Direction of Fall

3rd Cut -

Hinge

 

Felling Cut

2nd Cut -

 

 

 

 

Upper

 

 

 

 

2"

 

Notch

 

 

Cut

1st Cut -

2"Lower Notch Cut

B) Felling Cut

1.Make felling cut two inches higher than lower notch cut and on opposite side of tree (see Figure 15, page 14). Keep fell- ing cut parallel to lower notch cut.

2.Cut towards notch.

3.As felling cut nears hinge, tree should be- gin to fall. Note: If needed, drive wedges into felling cut to control direction of fall. If tree settles back and pinches chain, drive wedges into felling cut to remove saw. Only use wedges made of wood, plastic, or aluminum. Never use wedge made of steel. This could cause kickback and damage to chain.

4.When tree begins to fall, quickly

•remove saw from felling cut

•release trigger to turn saw off

•put saw down

•exit area using retreat path

WARNING: Do not cut all the way through tree. Leave about two inches of tree diameter uncut directly behind felling notch (see Figure 15). This uncut portion acts as a hinge. The hinge helps keep tree from twisting and falling in wrong direction.

WARNING: Be alert for falling overhead limbs. Watch your footing while exiting area.

Limbing a Tree

WARNING: Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 5, to avoid risk of kickback.

WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood spring- ing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death.

Limbing is removing branches from a fallen tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 16). Clear cut limbs from work area often. This will help maintain a safe work area.

Make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb. Start cut on limbs under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove saw.

ENGLISH

Figure 15 - Felling A Tree

Figure 16 - Limbing A Tree

www.desatech.com

13

ww.desatech.com

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Volt Cordless Chainsaw Stop Introduction ContentsBefore Operating Saw Important Safety InformationWhile Operating Saw Maintenance Storage of Saw IMPORTANT Safety InformationKickback General Maintenance Polesaw Trimming PrecautionsService StorageChain Saw Product IdentificationPoleSaw Rear Handle Handle located at rear of saw body Chain SAW terms and definitionsReduced Kickback Guide Bar Guide Bar that reduces chance of kickbackProtective Battery Terminal Cap Rechargeable batterySafety Warnings 10.0Important Charging Notes Charging BatterySaw Chain Tension Adjustment Chain Saw AssemblyLoosen guide bar nuts before adjust- ing chain see Figure Chain Saw InformationFelling a Tree Cutting Down a Tree Oiling ChainCutting with the Chain Saw Before Felling a TreeLimbing a Tree Felling Procedure Felling NotchFelling Cut Cut towards notchTrimming a Tree Pruning Bucking a LogLog Supported On One End Entire Length Of Log On GroundAdjusting Pole Length Polesaw AssemblyPolesaw Information Cutting with the PolesawCleaning Saw Body Cleaning and MaintenanceCare of Guide Bar Sharpening Saw ChainFiling Cutter Depth Gauges Replacing Saw ChainPlace sprocket cover onto guide bar bolts Observed Fault Possible Cause Remedy TroubleshootingNon-Warranty Service Warranty ServiceSee pages 43 through 44 for an Illustrated Parts List Box Warranty InformationManual Para EL Usuario Introducción Diagnóstico Y Resolución DE ProblemasEntificación del Producto Información sobre la sierra de cadenaAntes DE Utilizar LA Sierra Información Importante DE SeguridadAl utilizar la sierra Al cortar, no aplique gra fuerza a la sierra ContragolpesCómo llevar la sierra Mantenimiento de la cadena y seguridad contra contragolpes AlmacenamientoInspeccione la cadena serrada antes y después de cada uso Mantenimiento GeneralPrecauciones al recortar con la sierra de pértiga DesembalajePoleSaw Cadena Identificación del ProductoTérminos y definiciones de la sierra de cadena Tapa protectora del terminal de la batería Batería recargableAdvertencias de Seguridad Cord AWG CordNotas importantes sobre la carga Carga de la bateríaTensión de la sierra de cadena Ensamblado de la sierra de cadenaLubricación DE LA Cadena Ajuste DE Tensión DE LA Cadena SerradaRealización DE Cortes Advertencia Tala DE UN Árbol Derribamiento de un árbolAntes de derribar un árbol Procedimiento de tala Corte de la muescaTrozado DE UN Tronco Desmembramiento DE UN ÁrbolLa totalidad del tronco sobre el suelo Tronco apoyado en un extremoFigura 20- Poda de una rama Poda DE UN ÁrbolInformación sobre la sierra de Pértiga Corté CON LA Sierra DE Pértiga Regulación DE LA Longitud DE LA PértigaLimpieza DEL Cabezal Limpieza Y MantenimientoCuidado DE LA Barra DE Guía Afilado DE LA CadenaLimado de los calibradores de medida de profundidad Recambio de la cadena serradaAjuste bien la barra guía con la llave Diagnóstico Y Resolución DE Problemas Accesorios Y Piezas DE Repuesto Servicio TécnicoServicio DE Reparación Servicio con garantíaGarantía Estándar de la Batería Garantía EstándarGarantía Limitada Illustrated Parts LIST/DESGLOSE Ilustrado DE Partes BS188A Parts LIST/LISTA DE RepuestosParts Centrals / Central DE Piesaz 121071-01 REV.A 11/07

BS188A, BPS188A, BS188A, BPS188A, BS188A specifications

Remington Power Tools has established a reputation for manufacturing high-quality equipment that meets the needs of both professional tradespeople and DIY enthusiasts. Among their wide array of tools, the BS188A and BPS188A models stand out as versatile and reliable options for various tasks.

The BS188A is a powerful and efficient tool designed for heavy-duty job applications. It features a robust motor that provides exceptional performance, ensuring that it can handle even the toughest materials with ease. The lightweight design allows for extended usage without causing fatigue, making it suitable for a wide range of tasks, from woodworking to metalworking.

One of the standout features of the BS188A is its variable speed control, which provides users the flexibility to adjust the tool's speed according to the specific requirements of their project. This feature enhances precision and ensures that users can achieve the desired results consistently. Additionally, the tool comes with an ergonomic handle that provides a comfortable grip, reducing strain during operation.

The BPS188A model complements the BS188A by offering added versatility with a broader range of applications. It includes advanced technology such as an automatic feed system that enables users to work more efficiently, minimizing downtime between tasks. This feature streamlines workflows, making it easier to tackle larger projects without interruptions.

Another notable characteristic of the BPS188A is its high-capacity battery, which ensures longer run times and faster charging. This provides an added layer of convenience, as users can work longer hours without worrying about running out of power. Furthermore, the inclusion of LED indicators helps to keep track of battery life, allowing users to recharge when necessary.

Both models also prioritize user safety, incorporating features such as overload protection and a quick-stop function. These safety measures are crucial in preventing accidents and ensuring that users can operate the tools with confidence, regardless of their experience level.

In summary, the Remington Power Tools BS188A and BPS188A models combine performance, versatility, and safety. With their powerful motors, ergonomic designs, and advanced features, these tools are perfect for anyone looking to enhance their productivity and tackle various projects with ease. Whether for professional use or personal projects, these tools deliver reliability and efficiency.
Top Page Image Contents