Remington Power Tools BS188A, BPS188A, BS188A owner manual Polesaw Information, Polesaw Assembly

Page 15

Polesaw Information

Polesaw Assembly

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

1.Remove battery from chain saw.

2.Separate main handle from chain saw power head by pressing both release buttons on main handle and pulling apart (see Figure 21).

Press

Release

Release

Button

Buttons

 

Figure 21- Separate Main Handle from Powerhead.

3.Align rib on chain saw power head with groove in power head adapter on pole (see Figure 22).

Groove

Groove

Rib

Polesaw

Handle

Adapter

Main Handle

Figure 24 - Align Main Handle with Han- dle Adapter

6.Slide main handle into handle adapter until units “snap” together (see Figure 25). IMPORTANT: Both release but- tons on main handle must be fully engaged.

3.To lock pole in position, tighten clamping lever (see Figure 27).

UNLOCKLOCK

Figure 27 - Extending Telescopic Pole

Cutting with the Polesaw

1.Attach battery to saw.

2.Use both hands to grip polesaw. Use only designated grip areas when oper- ating polesaw (see Figure 28). Use firm grip. Thumbs and fingers must wrap around polesaw handle and pole.

3.Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.

ENGLISH

Rib

Power Head

Polesaw

Power Head

Adapter

Figure 22 - Align Power Head with Power Head Adapter

4.Slide power head into power head adapter until units “snap” together (see Figure 23). IMPORTANT: Both release buttons on power head adapter must be fully engaged.

Figure 23 - Assembled Power Head and Power Head Adapter

5.Align rib on handle adapter on pole with groove in main handle (see Figure 24).

Figure 25 - Assembled Main Handle and Handle Adapter

7.Slide battery onto main handle until release buttons “snap” together (see Figure 26).

Note: Fully charge battery before using for first time. See Charging Battery, page 10

Main Handle

Battery

Figure 26 - Assembled Battery onto Main Handle

Adjusting Pole Length

The Remington brand polesaw has a tele- scoping pole assembly that will extend from 47 inches (fully retracted) to 83 inches (fully extended). A cam levered collet is used to hold the pole in position at any extended length.

1.To extend the pole, loosen the clamping lever (see Figure 27). Pole will slide freely.

2.Pull inner pole section out to desired length of extension. Note: Only extend pole to minimum length required to reach limb that is being cut.

Grip Area

Figure 28- Designated Grip Areas

4.When ready to make a cut, press in trigger lockout and squeeze trigger (see Figure 29). This will turn polesaw on. Releasing trigger will turn polesaw off. Make sure saw is running before starting a cut.

5.When starting a cut, place moving chain against wood. Hold polesaw firmly in place to avoid possible bounc- ing or skating (sideways movement) of saw.

6.Guide polesaw using light pressure. Do not force saw. The motor will overload and can burn out. It will do the job bet- ter and safer at the rate for which it was intended.

7.Remove polesaw from a cut with saw running. at full speed. Stop polesaw by releasing trigger. Make sure chain has stopped before setting polesaw down.

Trigger

Trigger Lockout

Figure 29- Polesaw Handle with Trigger Lockout

www.desatech.com

15

ww.desatech.com

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Volt Cordless Chainsaw Stop Introduction ContentsImportant Safety Information Before Operating SawWhile Operating Saw IMPORTANT Safety Information Maintenance Storage of SawKickback Storage Polesaw Trimming PrecautionsGeneral Maintenance ServiceProduct Identification Chain SawPoleSaw Bar that reduces chance of kickback Chain SAW terms and definitionsRear Handle Handle located at rear of saw body Reduced Kickback Guide Bar Guide10.0 Rechargeable batteryProtective Battery Terminal Cap Safety WarningsImportant Charging Notes Charging BatteryChain Saw Information Chain Saw AssemblySaw Chain Tension Adjustment Loosen guide bar nuts before adjust- ing chain see FigureBefore Felling a Tree Oiling ChainFelling a Tree Cutting Down a Tree Cutting with the Chain SawCut towards notch Felling Procedure Felling NotchLimbing a Tree Felling CutEntire Length Of Log On Ground Bucking a LogTrimming a Tree Pruning Log Supported On One EndCutting with the Polesaw Polesaw AssemblyAdjusting Pole Length Polesaw InformationSharpening Saw Chain Cleaning and MaintenanceCleaning Saw Body Care of Guide BarReplacing Saw Chain Filing Cutter Depth GaugesPlace sprocket cover onto guide bar bolts Observed Fault Possible Cause Remedy TroubleshootingWarranty Service Non-Warranty ServiceSee pages 43 through 44 for an Illustrated Parts List Box Warranty InformationManual Para EL Usuario Información sobre la sierra de cadena Diagnóstico Y Resolución DE ProblemasIntroducción Entificación del ProductoInformación Importante DE Seguridad Antes DE Utilizar LA SierraAl utilizar la sierra Contragolpes Al cortar, no aplique gra fuerza a la sierraCómo llevar la sierra Mantenimiento General AlmacenamientoMantenimiento de la cadena y seguridad contra contragolpes Inspeccione la cadena serrada antes y después de cada usoPrecauciones al recortar con la sierra de pértiga DesembalajePoleSaw Cadena Identificación del ProductoTérminos y definiciones de la sierra de cadena Cord AWG Cord Batería recargableTapa protectora del terminal de la batería Advertencias de SeguridadNotas importantes sobre la carga Carga de la bateríaTensión de la sierra de cadena Ensamblado de la sierra de cadenaAjuste DE Tensión DE LA Cadena Serrada Lubricación DE LA CadenaRealización DE Cortes Procedimiento de tala Corte de la muesca Tala DE UN Árbol Derribamiento de un árbolAdvertencia Antes de derribar un árbolTronco apoyado en un extremo Desmembramiento DE UN ÁrbolTrozado DE UN Tronco La totalidad del tronco sobre el sueloFigura 20- Poda de una rama Poda DE UN ÁrbolInformación sobre la sierra de Pértiga Corté CON LA Sierra DE Pértiga Regulación DE LA Longitud DE LA PértigaAfilado DE LA Cadena Limpieza Y MantenimientoLimpieza DEL Cabezal Cuidado DE LA Barra DE GuíaRecambio de la cadena serrada Limado de los calibradores de medida de profundidadAjuste bien la barra guía con la llave Diagnóstico Y Resolución DE Problemas Servicio con garantía Servicio TécnicoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónGarantía Estándar Garantía Estándar de la BateríaGarantía Limitada Illustrated Parts LIST/DESGLOSE Ilustrado DE Partes BS188A Parts LIST/LISTA DE RepuestosParts Centrals / Central DE Piesaz 121071-01 REV.A 11/07

BS188A, BPS188A, BS188A, BPS188A, BS188A specifications

Remington Power Tools has established a reputation for manufacturing high-quality equipment that meets the needs of both professional tradespeople and DIY enthusiasts. Among their wide array of tools, the BS188A and BPS188A models stand out as versatile and reliable options for various tasks.

The BS188A is a powerful and efficient tool designed for heavy-duty job applications. It features a robust motor that provides exceptional performance, ensuring that it can handle even the toughest materials with ease. The lightweight design allows for extended usage without causing fatigue, making it suitable for a wide range of tasks, from woodworking to metalworking.

One of the standout features of the BS188A is its variable speed control, which provides users the flexibility to adjust the tool's speed according to the specific requirements of their project. This feature enhances precision and ensures that users can achieve the desired results consistently. Additionally, the tool comes with an ergonomic handle that provides a comfortable grip, reducing strain during operation.

The BPS188A model complements the BS188A by offering added versatility with a broader range of applications. It includes advanced technology such as an automatic feed system that enables users to work more efficiently, minimizing downtime between tasks. This feature streamlines workflows, making it easier to tackle larger projects without interruptions.

Another notable characteristic of the BPS188A is its high-capacity battery, which ensures longer run times and faster charging. This provides an added layer of convenience, as users can work longer hours without worrying about running out of power. Furthermore, the inclusion of LED indicators helps to keep track of battery life, allowing users to recharge when necessary.

Both models also prioritize user safety, incorporating features such as overload protection and a quick-stop function. These safety measures are crucial in preventing accidents and ensuring that users can operate the tools with confidence, regardless of their experience level.

In summary, the Remington Power Tools BS188A and BPS188A models combine performance, versatility, and safety. With their powerful motors, ergonomic designs, and advanced features, these tools are perfect for anyone looking to enhance their productivity and tackle various projects with ease. Whether for professional use or personal projects, these tools deliver reliability and efficiency.
Top Page Image Contents