Remington BS188A, BPS188A owner manual Chain SAW Information, Chain SAW Assembly, SAW Chain Tension

Page 11

CHAIN SAW INFORMATION

CHAIN SAW ASSEMBLY

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

1.Align rib on chain saw power head with groove in main handle (see Figure 5).

2.Slide power head into main handle until units “snap” together (see Figure 6). IMPORTANT: Both release buttons on main handle must be fully engaged.

3.Slide battery onto main handle until release buttons “snap” together (see Figure 7).

Note: Fully charge battery before using for first time. See Charging Battery.

NOTE: Your Remington Cordless Polesaw and Cordless Chainsaw may have been purchased together (as a 2-in-1 polesaw/ chainsaw) or seperate (chainsaw only). If the chainsaw was purchased separately, the pole is available as an accessory and may be purchased by visiting the "On-Line Outlet" at www.desatech.com.

Groove

Rib

Main

Handle

Power Head

Figure 5 - Align Power Head with

Handle

Figure 6 - Assembled Power Head Main Handle

Main Handle

Battery

Figure 7 - Assemble Battery onto Main

Handle

SAW CHAIN TENSION

WARNING: Remove battery from chainsawbeforeadjustingsawchain tension. Severe injury or death could occur from body contact with moving chain.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: Maintain proper chain tension always.Aloose chain will increase the risk of kickback.A loose chain may jump out of guide bar groove. This may injure op- erator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly.

Note: The saw chain tension is properly set at the factory. A new chain will stretch. Check new chain tension frequently (after discon- necting battery) during the first 2 hours of operation. Allow chain to cool down. Follow steps below to check saw chain tension.

1.Remove battery from chain saw.

2.Place chain saw on a firm surface to check chain tension.

3.Pull chain with light force 1/8" away from bottom of guide bar and release (see Figure 8). If chain lightly snaps back into place, tension is correct. A slight sag (1/16" or less) between chain and bottom of guide bar is acceptable.

Figure 8 - Check Chain Tension

Saw Chain Tension Adjustment

1.Loosen guide bar nuts before adjust- ing chain (see Figure 9).

Guide Bar Nuts

Figure 9 - Loosen Guide Bar Nuts

2.Turn adjusting screw on front of power head clockwise until slack is out of chain (see Figure 10).

3.Wearing protective gloves, pull down on chain to check chain tension (See Step 3 Saw Chain Tension).

Adjusting

Screw

Figure 10 - Turning Adjusting Screw

ENGLISH

11

www.remingtonpowertools.com

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Volt Cordless Polesaw Volt Cordless Chainsaw Stop English Introduction ContentsWhile Operating SAW Important Safety InformationBefore Operating SAW Kickback Maintenance Storage of SAWUnpacking Polesaw Trimming PrecautionsGeneral Maintenance ServiceProduct Identification Chain SAWRear Handle Handle located at rear of saw body Chain SAW Terms and Definitions10.0 Rechargeable BatterySafety Warnings Important Charging Notes Charging BatteryChain SAW Information Chain SAW AssemblySaw Chain Tension Adjustment Loosen guide bar nuts before adjust- ing chain see FigureBefore Felling a Tree Oiling ChainCutting with the Chain SAW Cut towards notch Felling Procedure Felling NotchLimbing a Tree Felling CutLog Supported On One End Bucking a LOGTrimming a Tree Pruning Entire Length Of Log On GroundCutting with the Polesaw Polesaw AssemblyAdjusting Pole Length Polesaw InformationSharpening SAW Chain Cleaning and MaintenanceCleaning SAW Body Care of Guide BARPlace sprocket cover onto guide bar bolts Replacing SAW ChainFiling Cutter Depth Gauges See pages 43 through 44 for an Illustrated Parts List Warranty ServiceNON-WARRANTY Service Observed Fault Possible Cause Remedy TroubleshootingBox Bowling Green, KY Warranty InformationEspañol Manual Para EL UsuarioIntroducción EL Contiendo Diagnóstico Y Resolución DE ProblemasAL Utilizar LA Sierra Información Importante DE SeguridadAntes DE Utilizar LA Sierra Cómo llevar la sierra ContragolpesPermanezca alerta. Utilice el sentido común Al cortar, no aplique gra fuerza a la sierraMantenimiento General Mantenimiento Y Almacenamiento DE SU Sierra EléctricaAlmacenamiento Mantenimiento de la cadena y seguridad contra contragolpesPrecauciones AL Recortar CON LA Sierra DE Pértiga DesembalajeSierra DE Cadena Identificación DEL ProductoRetroceso Contragolpe, Presión Términos Y Definiciones DE LA Sierra DE CadenaCadena de contragolpe reducido Extremo frontal de la barra de guíaAdvertencias DE Seguridad Batería RecargableTapa Protectora DEL Terminal DE LA Batería Notas Importantes Sobre LA Carga Carga DE LA BateríaTensión DE LA Sierra DE Cadena Ensamblado DE LA Sierra DE CadenaSujete la batería a la sierra Ajuste DE Tensión DE LA Cadena SerradaLubricación DE LA Cadena Realización DE CortesTala final AdvertenciaAntes de derribar un árbol Procedimiento de tala Corte de la muescaTronco apoyado en un extremo Desmembramiento DE UN ÁrbolTrozado DE UN Tronco La totalidad del tronco sobre el sueloDe contragolpes, lea la sección Contragolpes en la página Poda DE UN ÁrbolPodar un árbol es el proceso de cortar ramas Ensamblado DE LA Sierra DE Pértiga Información Sobre LA Sierra DE PértigaCorté CON LA Sierra DE Pértiga Regulación DE LA Longitud DE LA PértigaAfilado DE LA Cadena Limpieza Y MantenimientoLimpieza DEL Cabezal Cuidado DE LA Barra DE GuíaLimado de los calibradores de medida de profundidad Recambio DE LA Cadena SerradaServicio CON Garantía Servicio TécnicoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónPor completo Diagnóstico Y Resolución DE ProblemasLa batería está casi descargada Modelo Fecha de compra Garantía EstándarGarantía Estándar de la Batería Garantía LimitadaEspañol Illustrated Parts LIST/DESGLOSE Ilustrado DE Partes BS188A Parts LIST/LISTA DE RepuestosParts Centrals / Central DE Piesaz Page REV.B

BS188A, BPS188A specifications

The Remington BPS188A and BPS188A models represent a significant advance in the line of tactical shotguns, designed to meet the diverse demands of shooting enthusiasts and professionals alike. These models are characterized by their innovative features, robust construction, and user-friendly operation, making them ideal for both home defense and competitive shooting.

One of the standout features of the BPS188A is its pump-action mechanism, which offers reliable cycling and smooth operation. This allows for rapid follow-up shots, a crucial advantage in high-pressure scenarios. The shotgun is equipped with a 28-inch barrel that enhances accuracy while providing a good balance for handling. The barrel is manufactured from high-quality steel, ensuring durability and longevity while maintaining precision in various shooting conditions.

In terms of technology, the BPS188A integrates a dual-action bar system that ensures consistent performance, reducing the chances of jamming during operation. Additionally, the shotgun comes with an adjustable rear sight and a front bead sight, which facilitate fast target acquisition and improved aiming capability, crucial for effective shooting under varied conditions.

The BPS188A is designed with user comfort in mind. It features a synthetic stock and forend, which are resistant to weather effects and provide enhanced grip, even in wet conditions. The shotgun also has an ergonomic design that allows for comfortable handling and control, making it suitable for extended shooting sessions.

A notable characteristic of the BPS188A is its versatility. The shotgun is compatible with various ammunition types, ranging from birdshot to slugs, allowing users to customize their loadout based on specific needs or preferences. This flexibility makes it an excellent choice for diverse shooting applications, whether for sport or tactical scenarios.

In terms of safety, the BPS188A incorporates a cross-bolt safety mechanism, which is easily accessible and serves as an added layer of security against accidental discharges. The shotgun's overall build quality reflects Remington's commitment to craftsmanship, with every component engineered to ensure reliability and performance.

Overall, the Remington BPS188A and BPS188A are exemplary tactical shotguns that combine advanced features, comfortable design, and reliable performance. These models cater to a wide range of shooting applications, making them a valuable addition to any firearm enthusiast's collection. Whether for personal defense or recreational shooting, the BPS188A stands poised to deliver exceptional service and satisfaction.
Top Page Image Contents