RedMax BCZ2401S-CA manual Starting the Engine, Using the Product

Page 12

English

5. For safe operation

IMPORTANT

Remove any obstacle before beginning work.

3.Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened.

4.Be sure the debris guard is firmly attached in place.

5.If the cutting head is the metal blade, change the guard and handle, and attach the shoulder strap (see p42). Adjust the strap before starting the engine at the position that your left hand can comfortably hold the handlebar grip approximately waist high.

STARTING THE ENGINE

1.Keep bystanders and animals at least 50feet (15m) away from the operating point. If you are approached, immediately stop the engine.

2.The product is equipped with a centrifugal clutch mechanism, so the cutting attachment could rotate as soon as the engine is started. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts.

WARNING

Make sure the throttle is at idle position.

Never place the throttle into the high speed position or half throttle position (throttle lock position) when starting the engine.

3.After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position (idle position). If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair.

USING THE PRODUCT

IMPORTANT

Cut only materials recommended by the manufacturer. And use only for tasks explained in the manual.

12

Image 12
Contents BCZ2401S-CA Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Parts location Specifications BCZ2401S/BCZ2401S-CAEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Symbols on the machine PositionEmplacement PosiciónFor safe operation Working ConditionWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineDemarrage DU Moteur Arranque DEL MotorUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up Assemblage Montaje When using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 OP3 Starting EngineOP4 Stopping Engine OP3Fonctionnement Uso Arret DU Moteur OP3 Cómo Parar EL Motor OP3Adjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL Acelerador Reglage DU Ralenti OP6Travail DE Coupe Utilisation DE LA Tete a FIL Ajuste DE LA Velocidad DE Marcha EN Vacío OP6Adjusting the Line Length Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a Champion RZ7C MA4Spark Plug Tightening TorqueChampion RZ7C Couple DE SerrageSilencieux PARE-ETINCELLESMA6 Gear Case MA6Intake AIR Cooling Vent MA7Boitier DE Renvoi D’ANGLE MA6 Caja DE Engranajes MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Entretien Mantenimiento Rangement AlmacenamientoMise au rebut Eliminación SET UP the Hanger OPT1 Optional blade usageOPT1 OPT2 OPT3 OPT4 Hanger complete Shoulder strap T3300-17100Utilisation de la lame optionnelle Uso de hoja opcional Mise EN Place DE LA Fixation OPT1Monte EL Colgador OPT1 PAR TorsorSET UP the Blade OPT5 OPT6 OPT7Choose the Blade Balance UnitChoisir LA Lame Elija LA HojaMise EN Place DE LA Lame Monte LA Hoja Equilibrage DE LA MachineOPT8 OPT9 OPT10 OPT11 Cutting MethodOperation Methode DE Coupe FonctionnementMétodo DE Corte USOControlling Blade Thrust What causes blade thrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT12How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT12Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento HojaTroubleshooting guide 13. Guía de localización y solución de problemasGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ2401S/BCZ2401S-CA S/N 50200101 and up Optional Blade & Accessories Engine Unit BCZ2401S/BCZ2401S-CA S/N 50200101 and up Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control BCZ2401SMesures DE Lutte Contre LES Emissions Control DE Emisiones