Makita BBX7600CA Operation Method, Adjusting Shoulder strap, Adjusting the control lever

Page 14

OPERATION METHOD

1. Adjusting Shoulder strap

Adjust the shoulder strap to a length that is comfortable to work while carrying the blower.

Adjust as shown in the figure.

2. Adjusting the control lever

Move the control handle along the swivel pipe to the most comfortable position.

3. Blower operation

While operating the blower, adjust the throttle bar so that the wind force is appropriate for the work location and conditions.

Low speed: Dried leaves and grass

High speed: Gravel and dirt

The cruise control level allows the operator to maintain a constant engine RPM without operating the trigger lever.

Lifting the cruise control lever increases engine RPM. Lowering the cruise control lever decreases RPM.

Adjusting engine RPM when the cruise control lever is being used:

When increasing RPM:

￿Pull the trigger lever to increase engine RPM. Engine RPM returns to its original setting when the trigger lever is released.

￿Increasing the RPM in this manner also increases the cruise control setting. The cruise control lever lifts simultaneously as the trigger lever is pulled, and the new cruise control setting will be maintained at the higher RPM.

When reducing engine RPM:

￿Lower the cruise control lever to the low-speed position.

To tighten straps

To loosen straps

 

 

 

 

 

 

 

 

 

Cruise control lever

High-speed

Low-speed

TRANSPORTING AND STORING THE BLOWER

Please maintain the blower in an upright position whenever transporting or storing. (Refer to Figure at right.)

Transporting or storing in a position that is not upright may cause oil to spill inside the blower engine. This may result in oil leaks and white smoke from burning oil, and the air cleaner may become dirty with oil.

DANGER

•When transporting the blower, be sure to stop the engine.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Instructions D’EMPLOI English / Français / SpanishSymbols EnglishPersonal Protective Equipment Safety InstructionsGeneral Instructions Pay particular attention to the following regulationsRefueling Method of operation Maintenance instructionsWhen asking for help, please give the following information First AidTechnical Data Designation of Parts Designation of PartsAssembly Instructions Assembly of Blower PipesAttachment Procedure Attaching the Shoulder StrapBefore Starting the Engine Check Point #1 Concerning the oil cap when adding oilCheck Point #2 If oil is spilled when adding oil Checking and Refilling Engine OilFuel Fuel supplyStorage Period of Fuel Refueling MethodOperation StartingCheckup of low-speed rotation Adjustment of IdlingStopping Operation Method Adjusting Shoulder strapAdjusting the control lever Blower operationInspection and Maintenance Replacement of engine oilCleaning of air cleaner Checking the spark plugReplacement of gaskets and packings Cleaning the fuel filterCleaning of parts StorageFault location Troubleshooting Makita Limited ONE Year Warranty Emission Compliance Period Federal Emission Component Defect Warranty Miscellaneous Items Used in Above SystemsObtaining Warranty Service HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Every 8 hours daily Every 8 hours dailySymboles FrençaisEquipements de protection Consignes DE SecuriteGénéralités Mise en route de l’appareilPlein de carburant Premiers secours MaintenanceFonctionnement ConditionnementCaractéristiques Techniques Liste DES Pièces Instructions DE Montage Montage du tube de soufflanteFixation de la bandoulière Procédure de fixationPrécaution Avant DE Démarrer LE MoteurVérification et remplissage de l’huile Durée de stockage du carburant Alimentation en carburantAvertissement CarburantFonctionnement Mise en marcheVerification de la rotation à petite vitesse Réglage DU RalentiArrêt Manoeuvre du souffleur Mode OperatoireRéglage de la bandoulière Transport ET Remisage DU SouffleurProcédure de changement de l’huile Inspection ET MaintenanceRemplacement de l’huile à moteur Nettoyage du filtre à air Vérification de bougie d’allumageNettoyage du filtre à carburant Remplacement des joints et garnituresRemisage Contrôle des boulons, écrous et visLocalisation des défauts Depannage Garantie Limitée D’UN AN Makita Símbolos SpanishEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones Generales Preste una atención especial a las siguientes medidasReabasteciemiento MetrosPrimeros Auxilios Metodo DE FuncionamientoInstrucciones DE Mantenimiento EmbalajeDatos Técnicos Denominación DE Partes Instrucciones DE Montaje Ensamblaje de los tubos del sopladorInstalación de la correa al hombro Procedimiento de instalaciónPrecaución Antes DE Poner EN Marcha EL MotorInspección y rellenado de aceite de motor Período de almacenamiento del combustible AlarmaAbastecimiento de combustible CombustibleOperación Modo de arranqueModo de parar Ajuste DEL RalentíNota PrecauciónAjuste la palanca de control Procedimiento DE OperaciónAjuste de la correa al hombro Operación del SopladorInspección Y Mantenimiento Cambio del aceite del motorLimpieza del depurador de aire Inspección de la bujía de alta tensiónInspección de pernos, tuercas y tornillos AlmacenamientoLimpieza del filtro de combustible Limpieza de piezasLocalización de averías Investigación DE Averías Garantía Limitada Makita DE UN AÑO 11-8, Sumiyoshi-cho Anjo, Aichi 446-8502, Japan
Related manuals
Manual 68 pages 49.92 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.
Top Page Image Contents