Makita BBX7600CA instruction manual Federal Emission Component Defect Warranty

Page 22

FEDERAL EMISSION COMPONENT DEFECT WARRANTY

EMISSION COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applicable in all States, except the State of California

Makita U.S.A., Inc., (herein "Makita") warrant to the initial retail purchaser and each subsequent owner, that this utility equipment engine (herein "engine") was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fall to conform with EPA regulations during its warranty period.

For the components listed under PARTS COVERED, the dealer or service center authorized by Makita will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.

EMISSION COMPONENT DEFECT WARRANTY PERIOD

The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.

PARTS COVERED

Listed below are the parts covered by the Emission Component Defect Warranty. Some of the parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement point for that part.

1) Fuel Metering System

3) Ignition System

(i)

Carburetor and internal parts

(i)

Spark plug

(ii)

Fuel filter, if applicable

(ii)

Flywheel Magneto

(iii)

Throttle stopper, if applicable

(iii)

Ignition Coil

(iv) Choke System, if applicable

 

 

2) Air Induction System

4) Miscellaneous Items Used in Above Systems

(i)

Air cleaner plate

(i)

Fuel hoses, clamps and sealing gaskets

(ii)Air cleaner case

(iii)Air cleaner element

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Instructions D’EMPLOI English / Français / SpanishSymbols EnglishPersonal Protective Equipment Safety InstructionsGeneral Instructions Pay particular attention to the following regulationsRefueling Method of operation Maintenance instructionsWhen asking for help, please give the following information First AidTechnical Data Designation of Parts Designation of PartsAssembly Instructions Assembly of Blower PipesAttachment Procedure Attaching the Shoulder StrapBefore Starting the Engine Check Point #1 Concerning the oil cap when adding oilCheck Point #2 If oil is spilled when adding oil Checking and Refilling Engine OilFuel Fuel supplyStorage Period of Fuel Refueling MethodOperation StartingStopping Adjustment of IdlingCheckup of low-speed rotation Operation Method Adjusting Shoulder strapAdjusting the control lever Blower operationInspection and Maintenance Replacement of engine oilCleaning of air cleaner Checking the spark plugReplacement of gaskets and packings Cleaning the fuel filterCleaning of parts StorageFault location Troubleshooting Makita Limited ONE Year Warranty Emission Compliance Period Federal Emission Component Defect Warranty Miscellaneous Items Used in Above SystemsObtaining Warranty Service HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Every 8 hours daily Every 8 hours dailySymboles FrençaisEquipements de protection Consignes DE SecuriteGénéralités Mise en route de l’appareilPlein de carburant Premiers secours MaintenanceFonctionnement ConditionnementCaractéristiques Techniques Liste DES Pièces Instructions DE Montage Montage du tube de soufflanteFixation de la bandoulière Procédure de fixationVérification et remplissage de l’huile Avant DE Démarrer LE MoteurPrécaution Durée de stockage du carburant Alimentation en carburantAvertissement CarburantFonctionnement Mise en marcheArrêt Réglage DU RalentiVerification de la rotation à petite vitesse Manoeuvre du souffleur Mode OperatoireRéglage de la bandoulière Transport ET Remisage DU SouffleurRemplacement de l’huile à moteur Inspection ET MaintenanceProcédure de changement de l’huile Nettoyage du filtre à air Vérification de bougie d’allumageNettoyage du filtre à carburant Remplacement des joints et garnituresRemisage Contrôle des boulons, écrous et visLocalisation des défauts Depannage Garantie Limitée D’UN AN Makita Símbolos SpanishEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones Generales Preste una atención especial a las siguientes medidasReabasteciemiento MetrosPrimeros Auxilios Metodo DE FuncionamientoInstrucciones DE Mantenimiento EmbalajeDatos Técnicos Denominación DE Partes Instrucciones DE Montaje Ensamblaje de los tubos del sopladorInstalación de la correa al hombro Procedimiento de instalaciónInspección y rellenado de aceite de motor Antes DE Poner EN Marcha EL MotorPrecaución Período de almacenamiento del combustible AlarmaAbastecimiento de combustible CombustibleOperación Modo de arranqueModo de parar Ajuste DEL RalentíNota PrecauciónAjuste la palanca de control Procedimiento DE OperaciónAjuste de la correa al hombro Operación del SopladorInspección Y Mantenimiento Cambio del aceite del motorLimpieza del depurador de aire Inspección de la bujía de alta tensiónInspección de pernos, tuercas y tornillos AlmacenamientoLimpieza del filtro de combustible Limpieza de piezasLocalización de averías Investigación DE Averías Garantía Limitada Makita DE UN AÑO 11-8, Sumiyoshi-cho Anjo, Aichi 446-8502, Japan
Related manuals
Manual 68 pages 49.92 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.
Top Page Image Contents