Husqvarna 327RD manual Maintenance schedule, Maintenance Daily Weekly Monthly

Page 30

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorized service workshop.

Maintenance

Daily

 

Weekly

Monthly

maintenance

maintenance

maintenance

 

 

 

 

 

 

Clean the outside of the machine.

 

X

 

 

 

 

 

 

 

Check that the harness is not damaged.

 

X

 

 

 

 

 

 

 

Check that the suspension ring is not damaged.

 

X

 

 

 

 

 

 

 

Make sure the throttle trigger lock and the throttle function

 

X

 

 

correctly from a safety point of view.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the stop switch works correctly.

 

X

 

 

 

 

 

 

 

Check that the handle and handlebar are undamaged and

 

X

 

 

secured correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the cutting attachment does not rotate at idle.

 

X

 

 

 

 

 

 

 

Clean the air filter. Replace if necessary.

 

X

 

 

 

 

 

 

 

Check that the guard is undamaged and not cracked. Replace the

 

X

 

 

guard if it has been exposed to impact or is cracked.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the blade is correctly centred, is sharp, and is not

 

 

 

 

cracked. An off-centre blade will cause vibration that could result

 

X

 

 

in damage to the machine.

 

 

 

 

 

 

 

 

 

Check that the trimmer head is undamaged and not cracked.

 

X

 

 

Replace the trimmer head if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the locking nut of the cutting equipment is tighten

 

X

 

 

correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check that nuts and screws are tight.

 

X

 

 

 

 

 

 

 

Check that there are no fuel leaks from the engine, tank or fuel

 

X

 

 

lines.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the transport guard for the blade is intact and that it

 

X

 

 

can be secured correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check the starter and starter cord.

 

 

X

 

 

 

 

 

 

Check that the vibration damping elements are not damaged.

 

 

X

 

 

 

 

 

 

Clean the outside of the spark plug. Remove it and check the

 

 

 

 

electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the

 

 

X

 

spark plug. Check that the spark plug is fitted with a suppressor.

 

 

 

 

 

 

 

 

 

Clean the machine’s cooling system.

 

 

X

 

 

 

 

 

 

Clean or replace the spark arrestor screen on the muffler (only

 

 

X

 

applies to mufflers without a catalytic converter).

 

 

 

 

 

 

 

 

 

 

 

 

Clean the outside of the carburettor and the space around it.

 

 

X

 

 

 

 

 

 

Check that the bevel gear is filled three-quarters full with lubricant.

 

 

X

 

Fill if necessary using special grease.

 

 

 

 

 

 

 

 

 

 

 

 

Check the fuel filter from contamination and the fuel hose from

 

 

 

X

cracks or other defects. Replace if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check all cables and connections.

 

 

 

X

 

 

 

 

 

Check the clutch, clutch springs and the clutch drum for wear.

 

 

 

X

Replace if necessary by an autorized service workshop.

 

 

 

 

 

 

 

 

 

 

 

 

Replace the spark plug. Check that the spark plug is fitted with a

 

 

 

X

suppressor.

 

 

 

 

 

 

 

 

 

 

 

 

Check and clean the spark arrestor screen on the muffler (only

 

 

 

X

applies to mufflers fitted with a catalytic converter).

 

 

 

 

 

 

 

 

 

 

 

 

30 – English

Image 30
Contents 323RII 327RX-series KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the brush cutter?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Cutting attachment guardVibration damping system Quick release MufflerCutting equipment Locking nutCutting equipment Sharpening grass cutters and grass blades Sharpening the saw bladeGeneral rules Trimmer head Assembly Fitting the handlebar 323RIIFitting the handlebar 327Rx, 327RDx Assembly Assembling and dismantling the two-piece shaft 327RDxDismantling Assembling the cutting equipment Fit the nut G. The nut must be tightened to a torqueFitting other guards and cutting attachments Spreading the load on your shoulders Adjusting the harness and brush cutterStandard harness Correct heightFuel safety Fuel HandlingFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting StartingFor throttle handles with a start throttle lock StoppingStarter cord around your hand General working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Brush cutting with a saw blade Grass clearing using a grass blade Grass trimming with a trimmer headMaintenance CarburetorMuffler Cooling systemRemember the risk of fire Air filter Cleaning the air filterBevel gear Two-piece shaft 327RDxSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Emission Warranty Parts List Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T25 Page Page Page Page Original instructions 1153290-95