Black & Decker NST2118R, BDCD220RSR, DR260BR, NST1118R Replacing the Spool Figures 13,14,15

Page 10

REPLACING THE SPOOL (FIGURES 13,14,15)

 

• Remove battery from tool.

13

 

• Depress the tabs (j) and

 

k

remove the spool cap (k)

Replacement

from the spool housing (l) in

 

the trimmer head (figure 13).

spool

 

• For best results, replace

Model #

 

spool with Black & Decker

 

model # AF-100.

AF-100

 

• Grasp empty spool with one

 

 

hand and spool housing with

 

 

other hand and pull spool out.

j

j

 

 

l

• If lever (m) (figure 14) in

14

 

base of housing becomes

m

dislodged, replace in correct

 

position before inserting new

 

 

spool into housing.

 

o

• Remove any dirt and grass

 

 

from the spool and housing.

 

 

• Unfasten the end of the

 

 

cutting line and guide the line

 

 

into the eyelet (n) figure 15.

 

 

• Take the new spool and

 

 

push it onto the boss (o)

 

 

(figure 14) in the housing.

 

 

Rotate the spool slightly until it

 

n

is seated.

 

The line should protrude

 

 

approximately 5-3/8 inches (136mm) from the housing.

 

• Align the tabs on the spool

15

 

cap with theslots(p)in the

 

 

housing (figure 15).

 

 

• Push the cap onto the

 

 

housing until it snaps

 

 

securely into place.

 

 

CAUTION: To avoid tool

p

n

damage, if the cutting line

 

protrudes beyond the

 

 

trimming blade, cut it off so

 

 

that it just reaches the

 

 

blade.

 

 

REWINDING SPOOL FROM BULK LINE (USE ONLY .065 IN.

ROUND DIAMETER LINE) (FIGURES 16,17,18)

Bulk line is also available for purchase from your local retailer.

NOTE: Hand wound spools from bulk line are likely to become

tangled more frequently than Black & Decker factory wound

spools. For best results, factory wound spools are

recommended.

 

To install bulk line, follow the steps below:

• Remove battery from tool.

 

• Remove the empty spool

16

from the tool as described

in “REPLACING THE

q

SPOOL”.

 

• Remove any remaining

 

cutting line from the spool.

 

• Make a fold at the end of

r

the cutting line at about 3/4

inch (19mm)(q). Feed the

 

cutting line into one of the

 

line anchoring slots (r) as

 

shown in figure 16.

 

10

Image 10
Contents Please Read Before Returning This Product for ANY Reason Table of Contents InstructionsBattery CAP Information For Battery Chargers ComponentsCharging Procedure Pack charge initially for 9 hours. AfterImportant Charging Notes Leaving the Battery Pack in the ChargerStorage Recommendation 1.Store tool Installingthe Guard Attaching the Auxiliary Handle Assembly & AdjustmentAssembly Tools Required not Supplied Phillips ScrewdriverSwitching on and OFF Height AdjustmentOperating Instructions Convert to Edging Mode Replacement AccessoriesCutting Line / Line Feeding Round Diameter Line Figures 16,17,18 Replacing the Spool Figures 13,14,15Rewinding Spool from Bulk Line USE only .065 ReplacingMaintenance Battery Recycling and the Rbrc SealTroubleshooting Tool Runs Slowly Service Information Full TWO-YEAR Home USE WarrantySee ʻTools-Electricʼ For Service & SalesYellow Pages TAILLE-BORDURE / COUPE- BORDUREMODED’EMPLOI Directives Depremièreimportance Avertissements DE SécuritéetToujours Porter UNE Protection Oculaire Conserver CES Mesures Conçu spécialement pour filtrer lesparticulesmicroscopiques Minutes Courant alternatif Courant continueRévolutions ou Sécurité Renseignements Concernant LE Capuchon DE LA PileComposants Importantes Pour LES Chargeurs DE PilesProcedure DE Charge Remarques Importantes SUR LE Chargement Recommandations DʼENTREPOSAGEDES Réglages BLOC-PILES Laisse Dans LE ChargeurFixation DE LA Poignee Auxiliaire La figureReglage DE LA Hauteur Mise EN Marche ET ArretConvertir AU Mode COUPE-BORDURE Accessoires DE RechangeFIL Tranchant / Avance DU FIL Section « Remplacer LA Remplacer LA Bobine Figures 13, 14Bobine » Bobine » LʼOUTIL Fonctionne Lentement Toute question,communiquer avec le directeur du centre de Obtenir le remplacement gratuitÉlectriques » Pas destiné à un usagecommercialPodadora / Bordeadora Manual DE Instrucciones Utilice LA Vestimenta Adecuada no utilice ropa holgada Importantes Sobre SeguridadSiempre Utilice Protección Para LOS Ojos utilice LA Cuerda Giratoria Realiza UNA Función DEConserve Estas Instrucciones Terminal a tierra Los símbolos y sus definiciones son los siguientesCarga Informacion Sobre LA Tapade LA BateriaComponentes Importantes Para Cargadores DE BateríasHz figura Cable es apropiado para uso en el exteriorHoras Notas Importantes Sobre LA Carga Desenchufe el cargador y retireEl paquete de baterías en la Recomendacion Para EL AlmacenamientoENSAMBLADO/REGULACIONES Ajuste DE Altura Instrucciones DE OperacionLa figura Conversión AL Modo DE Bordeado Encendido Y ApagadoLa podadora en ángulos de lado a lado Como se muestra en la De la superficie como se muestra en laReemplazo DE Carretes Figuras 13,14,15 Accesorios DE RepuestoCubierta figura Pulgada DE Diametro Figuras 16, 17 Enrollado DEL Carrete CON Cuerda a GranelUtilice Solo Cuerda Redonda DE 1,7 MM 0,0065 Reemplazo DEL CarreteMantenimiento Deteccion DE Problemas LA Herramienta Funciona LentamenteRBRCEl sello Rbrc Corporación de reciclado de Garantia Completa DE DOS Anos Para USO EN EL Hogar Name · Nombre Años DE Garantia Esta Garantia no Aplica CuandoSolamente Para Propositos DE Mexico
Related manuals
Manual 2 pages 15.79 Kb Manual 36 pages 46.66 Kb

NST2118R, NST1118R, NST2118, BDCD220RSR, NST1118 specifications

Black & Decker has long been recognized as a leader in the power tools and outdoor equipment market, and their latest range of cordless tools continues this tradition of quality and innovation. Among the standout products are the BDCD220RSR, NST2118, NST1118, NST1118R, and NST2118R, each designed to meet the diverse needs of consumers and professionals alike.

The Black & Decker BDCD220RSR is a versatile 20V MAX cordless drill/driver that boasts a lightweight, compact design for easy handling. Its powerful lithium-ion battery ensures extended runtime and quick charging, allowing users to complete tasks without frequent interruptions. The drill features an 11-position clutch that helps to prevent stripping and overdriving screws, making it suitable for both wood and metal applications. Additionally, the integrated LED work light illuminates the workspace, enhancing visibility in dim conditions.

Moving on to the NST2118 and NST1118 series, these models focus on outdoor maintenance, particularly hedge trimming and grass cutting. The NST2118 is an 18V MAX cordless hedge trimmer equipped with dual-action blades that provide faster trimming and a cleaner cut. Its lightweight design reduces user fatigue, while the wrap-around handle allows for comfortable, multi-directional cutting. The included battery provides sufficient power for extended trimming sessions without the hassle of cords.

In contrast, the NST1118 and NST1118R are lightweight string trimmers designed for ease of use and efficiency. The NST1118 features a 20V MAX battery that ensures high performance, while the NST1118R offers a push-button feed system for quick line advancement without the need for manual adjustments. Both models combine power and precision for effortless trimming around edges and borders, catering to homeowners and landscapers alike.

Another noteworthy characteristic of these Black & Decker tools is their emphasis on user-friendly technology. Each model incorporates ergonomic grips to enhance comfort during prolonged use, reducing strain on the hands and wrists. Moreover, the tools are designed for easy maintenance, with simple mechanisms for replacing batteries and clearing line jams.

In summary, the Black & Decker BDCD220RSR, NST2118, NST1118, NST1118R, and NST2118R represent a commitment to quality, efficiency, and user-centered design. With their powerful performance, innovative features, and reliable battery technology, these tools are ideal choices for anyone looking to elevate their DIY or gardening projects.