Snapper BC25H, FB15250KW Starting the Engine, Engaging the Transmission, Before Starting Engine

Page 8

Operating the Mower

STARTING THE ENGINE

NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to your engine manual.

Before Starting Engine:

•Be sure that the unit is completely assembled, all fas- teners are tightened securely, and all safety guards and components are in place.

•Be sure to check engine's oil and gasoline*. (See engine manual for recommended oil and gasoline specifications.) Never check the engine while it is running or while you are smoking. Check only when engine is cold.

*All machines are shipped without oil or gasoline unless otherwise noted.

To Start Engine:

Recoil Start -

•Open fuel valve, located at bottom of fuel tank by turning knob counterclockwise.

•Set throttle control past the “START” position (fully Right to the double lines) to engage choke.

•Turn key on dash panel to “RUN” position.

•Grasp recoil handle and pull cord briskly. (You may have to pull several times before engine starts. If engine fails to start within a reasonable number of attempts, discontinue and check engine manual for further instructions.)

NOTE: Be sure recoil cord retracts fully into recoil unit. A slack recoil cord can cause serious personal injury and/or damage to unit.

Electric Start - (Optional)

•Open fuel valve, located at bottom of fuel tank by turning knob counterclockwise.

•Set throttle control past the “START” position (fully Right to the double lines) to engage choke.

•Turn ignition key on dash panel past “RUN” position to “START” to engage starter. (If engine fails to start within a reasonable period of time - generally 2-3 attempts of 5-6 seconds cranking time each, discon- tinue and check engine manual for further instruc- tions.)

To Shut Engine Down:

•Allow engine to idle for 2-3 minutes before shutting down.

•Set throttle control down to “SLOW” position.

•Turn key to “OFF” position.

NOTE: If you experience problems with your engine that cannot be satisfactorily resolved by following the instruc- tions contained within the engine manual, contact your local engine dealer. All engine service, warranty or oth- erwise, is required to be performed by a manufacturer- authorized service center.

ENGAGING THE TRANSMISSION

Your Field & Brush mower is equipped with a rugged hydrostatic transmission. The mower can be operated at variable speeds in both forward and reverse directions. Please read the following instructions in order to acquaint yourself with the mowers controls for safe oper- ation.

The traction drive system is engaged or disengaged through the Traction Drive control lever (Figure 4), locat- ed on the right side of the machine, when standing at the Operator's Controls.

•Engage the traction drive by moving the control lever to the DRIVE position. The brush mower can now be moved using the Traction Drive Controls.

Figure 4 - Traction Drive / Freewheel Control

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual Table of Contents Safe Operation Practices for WALK-BEHIND Mowers General OperationSafety Rules and Information ServiceSlope Operation ChildrenSafety Rules & Information Safety DecalsDecal Warning Decal Engine Throttle ControlDecal Danger Dismemberment Decal Danger Flying ObjectsFeatures & Controls Control FunctionsStarting the Engine Engaging the TransmissionBefore Starting Engine To Start EngineTo Propel Unit In Reverse Operating the MowerTo Propel Unit Forward ENGAGING/DISENGAGING the Cutting Blade To Disengage Cutting BladeTo Adjust Cutting Height StorageRegular Maintenance Service Interval Every 25 HoursLubrication Lubricate Rear Axle ShaftsRegular Maintenance Battery ServiceCleaning the Battery and Cables 9HP Models Cleaning the Battery and Cables All Models Except 9HPServicing the Mower Blades Removing the BladeTroubleshooting Adjustment, & Service TroubleshootingTroubleshooting, Adjustment & Service TroubleshootingTroubleshooting, Adjustment, & Service Travel Control AdjustmentSerial Number Serial Number 012003001-UpBlade Clutch Adjustment Shut off engine before attempting this adjustment procedureBlade Brake Adjustment Mower Belt AdjustmentFor S/N 071601076 up Traction Drive Belt AdjustmentFor S/N 0 Troubleshooting, Adjustment & Service Mower Belt ReplacementSpecifications Parts & AccessoriesReplacement Parts Maintenance ItemsPage Products, Inc Macon Street/PO Box McDonough, GA

GM2513BS, GM2515KAW, BC25BE, BC25H, GM2513H specifications

The Snapper FB15250KW, GM2513H, BC25H, BC25BE, and GM2515KAW are a series of robust outdoor power equipment designed to tackle a variety of landscaping tasks. Each model comes with unique features and characteristics that cater to different user needs, ensuring efficient performance and reliability.

The Snapper FB15250KW is a versatile 21-inch push lawn mower equipped with a powerful 150cc engine. It features a 3-in-1 cutting system, allowing users to mulch, bag, or side discharge grass clippings. Its lightweight design and ergonomic handle make it easy to maneuver, while the adjustable cutting height provides flexibility for varying grass conditions. The easy-start engine technology ensures quick and reliable starting in any weather, making it a favorite for homeowners.

The GM2513H model is a gas-powered walk-behind mower that focuses on durability and performance. Its 25-inch cutting deck allows for larger mowing areas, perfect for medium to large lawns. This mower is equipped with self-propelling capabilities, which significantly reduces user effort during operation. The mower’s high rear wheels provide stability and traction on rough terrain, enhancing overall mowing efficiency.

For those looking for a string trimmer, the BC25H and BC25BE models offer exceptional performance. The BC25H features a powerful two-cycle engine and a straight shaft design, making it ideal for trimming hard-to-reach areas. Its lightweight build ensures maximum comfort during extended use. The BC25BE, similarly equipped with a robust engine, adds versatility by incorporating a detachable design for easy storage and transportation.

Lastly, the GM2515KAW is a high-performance riding mower tailored for extensive lawns. It boasts a powerful engine and a wide cutting deck, which cuts down mowing time significantly. The comfortable seat and adjustable steering provide an excellent user experience, allowing operators to navigate their lawns with ease. Additionally, the mower is designed with advanced safety features, ensuring user confidence during operation.

In summary, the Snapper FB15250KW, GM2513H, BC25H, BC25BE, and GM2515KAW cater to diverse landscaping needs, providing users with efficiency, ease of use, and reliability. These models embody Snapper's commitment to quality, making them ideal choices for both residential and professional applications in lawn care.
Top Page Image Contents