Snapper S200KAV2561, S200XK2761 manual Starting the Engine, Stopping the Rider

Page 21

Starting the Engine

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

1.While sitting in the operator’s seat, engage the parking brake by pulling the parking brake lever back, make sure the PTO switch is disengaged (pressed down fully) and the motion control handles are locked in the NEUTRAL position.

2.NOTE: A warm engine may not require choking.

Set the engine throttle control to FULL throttle position. Then fully close the choke by pulling the knob OUT fully.

3.Insert the key into the ignition switch and turn it to

START.

4.After the engine starts, gradually open the choke (push knob down fully). Reduce to half throttle speed and allow to warm up.

Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in STOPPING THE RIDER.

Stopping the Rider

1.Returning the ground speed control levers to the middle position will stop rider movement. Pivot the levers outward and lock them in NEUTRAL.

2.Disengage the PTO by pushing down on the PTO switch.

3.Engage the parking brake by pulling the handle up until it locks into position.

4.Move the throttle control to mid-throttle position and turn the ignition key to OFF. Remove the key.

Operation

Pushing the Rider By Hand

NOTICE

DO NOT TOW RIDER

Towing the units will cause hydraulic pump and wheel motor damage. Do not use another vehicle to push or pull this unit.

1.Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key.

2.Lift the seat plate to gain access to the hydraulic pumps.

3.To disengage the pumps (free-wheel position), turn the hydraulic release valves (A, Figure 8) located on the pumps COUNTER-CLOCKWISE a maximum of 2 full turns.

4.Disengage the parking brake.

The tractor can now be pushed by hand.

5.After moving the tractor, re-engage the pumps (drive position) by turning the release valves CLOCKWISE and tighten to 80-120 in. lbs. of torque.

A

Figure 8. Hydraulic System By-Pass

A.Hydraulic Release Valve (left-hand pump shown)

Operation

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model Number Description Briggs & Stratton Yard Power Products GroupNorth Main Street Munnsville, NYDate Purchased Table of Contents Operator Safety Operator SafetyOperating Safety Read the ManualSlope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Enclosed Areas Fuel and MaintenancePreparation TrainingOperation Or warnings which must be followedEmissions Towed Equipment RIDE-ON UnitsPeriods of exposure Do NotService and Maintenance Maintenance and StorageSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Operational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsSeat Adjustment Lever Features and ControlsIgnition Switch Control FunctionsFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingMowing Height Adjustment Seat AdjustmentCheck Tire Pressures Tire PressureRaise and Lower the Roll Bar Foot Pedal AdjustmentStarting the Engine Insert the key into the ignition switch and turn it toStopping the Rider Pushing the Rider By HandSmooth Travel Zero Turn Driving PracticeForward Travel Practice Forward Reverse TravelExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingMaintenance Schedule Regular MaintenanceSafety Items Before Every Spring Hours Fall Check Rider / Mower for loose hardwareEngine Maintenance Regular MaintenanceChecking / Adding Fuel Fuel FilterGrease LubricationOil Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Rod Timing Adjustment Deck Leveling AdjustmentRemove blocks from under the mower deck To avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Checking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryRegular Maintenance Starting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting TroubleshootingTroubleshooting Chart Troubleshooting the RiderNot drive Troubleshooting the MowerTroubleshooting Common Cutting Problems TroubleshootingDimensions SpecificationsEngine ChassisFerris Limited Warranty Product Specifications Common Service Parts TractorMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.
Top Page Image Contents