Snapper S200KAV2561, S200XK2761 manual Troubleshooting Chart, Troubleshooting the Rider

Page 43

Troubleshooting

Troubleshooting

Troubleshooting Chart

While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.

The troubleshooting guide below lists the most common problems, their causes and remedies.

See the information on the following pages for instructions on how to perform most of these minor adjustments and service repairs yourself. If you prefer, all of these procedures can be performed for you by your local authorized dealer.

WARNING

To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

Troubleshooting the Rider

Problem

Cause

Remedy

Engine will not turnover or start.

1.

Parking brake not engaged.

1.

Engage parking brake.

 

2.

PTO (electric clutch) switch

2.

Place in OFF position.

 

 

in ON position.

 

 

 

3.

Out of fuel.

3.

If engine is hot, allow it to cool, then refill

 

 

 

 

the fuel tank.

 

4.

Engine flooded.

4.

Move choke control to closed position.

 

5.

Fuse blown.

5.

Replace fuse.

 

6.

Battery terminals require

6.

Clean the battery terminals

 

 

cleaning.

 

 

 

7.

Battery discharged or dead.

7.

Recharge or replace.

 

8.

Wiring loose or broken.

8.

Visually check wiring & replace broken or

 

 

 

 

frayed wires. Tighten loose connections.

 

9.

Solenoid or starter motor faulty.

9.

Repair or replace. See authorized dealer

 

10.

Safety interlock switch

10. Replace as needed. See authorized

 

 

faulty.

 

service dealer.

 

11.

Spark plug(s) faulty, fouled

11. Clean and gap or replace.

 

 

or incorrectly gapped.

 

See engine manual.

 

12.

Water in fuel.

12. Drain fuel & replace with fresh fuel.

 

13.

Gas is old or stale.

13. Drain fuel & replace with fresh fuel.

 

 

 

 

 

Engine starts hard or runs poorly.

1.

Fuel mixture too rich.

1.

Clean air filter. Check choke adjustment.

 

2.

Spark plug faulty, fouled, or

2.

Clean and gap or replace.

 

 

incorrectly gapped.

 

(See engine manual.)

 

 

 

 

 

Engine knocks.

1.

Low oil level.

1.

Check/add oil as required.

 

2.

Using wrong grade oil.

2.

See engine manual.

 

 

 

 

 

Excessive oil consumption.

1.

Engine running too hot.

1.

Clean engine fins, blower screen and

 

 

 

 

air cleaner.

 

2.

Using wrong weight oil.

2.

See engine manual.

 

3.

Too much oil in crankcase.

3.

Drain excess oil.

 

 

 

 

 

Engine exhaust is black.

1.

Dirty air filter.

1.

Replace air filter. See engine manual.

 

2.

Engine choke control

2.

Open choke control.

 

 

is in closed position.

 

 

Maintenance

41

Image 43
Contents Munnsville, NY Briggs & Stratton Yard Power Products GroupModel Number Description North Main StreetDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetyThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Enclosed Areas Fuel and MaintenanceOr warnings which must be followed TrainingPreparation OperationDo Not Towed Equipment RIDE-ON UnitsEmissions Periods of exposureMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsControl Functions Features and ControlsSeat Adjustment Lever Ignition SwitchFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationTire Pressure Seat AdjustmentMowing Height Adjustment Check Tire PressuresRaise and Lower the Roll Bar Foot Pedal AdjustmentPushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderForward Reverse Travel Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting Turns Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Practice Turning In PlaceTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsHours Fall Check Rider / Mower for loose hardware Regular MaintenanceMaintenance Schedule Safety Items Before Every SpringFuel Filter Regular MaintenanceEngine Maintenance Checking / Adding FuelLubricating the Front Casters LubricationGrease OilChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentRemove blocks from under the mower deck To avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Jump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryRegular Maintenance Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartNot drive Troubleshooting the MowerTroubleshooting Common Cutting Problems TroubleshootingChassis SpecificationsDimensions EngineFerris Limited Warranty Tractor Product Specifications Common Service PartsMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.