Snapper S200KAV2561, S200XK2761 manual Neutral Adjustment, Parking Brake Adjustment

Page 34

Regular Maintenance

Neutral Adjustment

If the tractor “creeps” while the ground speed control levers are locked in NEUTRAL, then it may be necessary to adjust the linkage rod.

NOTE: Perform this adjustment on a hard, level surface such as a concrete floor.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.There are three nuts (B, Figure 34) on the linkage rod

(A). The first two are to be used together to turn the rod and the third (towards the front of the machine) is used to lock the rod in place. Loosen the jam nut that locks against the ball joint and turn the linkage rod to adjust. If the machine creeps forward, turn the rod CLOCKWISE (while standing at the rear of the machine, facing forward), if the machine creeps backward, turn the rod

COUNTER-CLOCKWISE.

3.Lock the jam nut (B) against the ball joint when neutral is achieved.

NOTE: This adjustment should not be performed while the machine is running. It may take several attempts to achieved neutral, depending upon how much the machine creeps.

 

 

A

 

 

B

Figure 34.

Neutral Adjustment

(LH side shown)

A.

Adjustment Linkage Rod

B.

Nuts

 

Maintenance

Parking Brake Adjustment

1.Disengage the PTO, stop the engine, block the front wheels, remove the ignition key, and engage the parking brake.

2.Locate the brake spring (A, Figure 35).

3.With the parking brake engaged, measure the compressed spring length. The spring should be 2” to 2-1/8” (5,0 - 5,4 cm) when compressed.

4.If the spring is not within this range, release the parking brake and turn the adjustment nut (B) to compress or release the spring.

5.Engage the parking brake and remeasure the spring.

CAUTION

Do not adjust the spring to be shorter than

1-15/16” (4,9 cm) when compressed. This may damage the brake mechanism.

If this does not correct the braking problem, see your Snapper Pro dealer.

 

2" - 2-1/8"

 

(5,0 - 5,4cm)

A

B

Figure 35. Parking Brake Adjustment

A.Brake Spring

B.Adjustment Nut

32

www.SnapperPro.com

Page 33 Page 35
Image 34
Page 33 Page 35
Contents North Main Street Briggs & Stratton Yard Power Products GroupModel Number Description Munnsville, NYDate Purchased Table of Contents Operating Safety Operator SafetyOperator Safety Read the ManualThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Fuel and Maintenance Enclosed AreasOperation TrainingPreparation Or warnings which must be followedPeriods of exposure Towed Equipment RIDE-ON UnitsEmissions Do NotMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Safety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsFeatures and Controls Identification NumbersIgnition Switch Features and ControlsSeat Adjustment Lever Control FunctionsFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentMowing Height Adjustment Tire PressureFoot Pedal Adjustment Raise and Lower the Roll BarStopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Pushing the Rider By HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Reverse TravelPractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingSafety Items Before Every Spring Regular MaintenanceMaintenance Schedule Hours Fall Check Rider / Mower for loose hardwareChecking / Adding Fuel Regular MaintenanceEngine Maintenance Fuel FilterOil LubricationGrease Lubricating the Front CastersChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentRemove blocks from under the mower deck Mower Belt Replacement To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Charging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryRegular Maintenance Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting Chart TroubleshootingTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Not driveTroubleshooting Troubleshooting Common Cutting ProblemsEngine SpecificationsDimensions ChassisFerris Limited Warranty Tractor Product Specifications Common Service PartsMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.
Top Page Image Contents