Snapper S200KAV2561, S200XK2761 manual Mowing Recommendations, Height of Grass

Page 24

Operation

Operation

Mowing

1.Engage the parking brake. Make sure the PTO switch is disengaged, the motion control levers are locked in the NEUTRAL position and the operator is on the seat.

2.Start the engine (see Starting The Engine).

3.Set the mower cutting height (see Mowing Height Adjustment).

4.Set the throttle to FULL.

5.Engage the PTO by pulling up on the PTO switch.

6.Begin mowing. See Mowing Recommendations for tips on mowing patterns, lawn care, and trouble shooting information.

7.When finished, shut off the PTO by pushing the PTO switch down completely..

8.Stop the engine (see Stopping The Rider and Engine).

Mowing Recommendations

Several factors can affect how well your machine cuts grass, Following proper mowing recommendations can improve the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference. Typically, you should mow the grass when it is is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass, the amount of rainfall, the prevailing temperature, and the lawn’s overall condition.

Cutting the grass too short causes weak, thin grass plants, which are easily damaged by dry periods and pests. Cutting too short is often more damaging than allowing the grass to be slightly higher.

Letting grass grow a bit longer—especially when it is hot and dry—reduces heat build-up, preserves needed moisture and protects the grass from heat damage and other problems. However, allowing grass to grow too high can cause thin turf and additional problems.

Cutting off too much at one time shocks the plant’s growth system and weakens the grass plants. A good rule of thumb is the 1/3 rule: to cut no more than one third of the grass height, and never more than 1 inch at a time.

The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using (for example, broadcasting with side discharge decks can process a much larger volume of grass than mulching does).

Figure 15. Proper Cutting Height

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum for the first pass, and then reset it to the desired height and mow a second or third time.

Don’t cover the grass surface with a heavy layer of clippings. Consider using a grass collection system and starting a compost pile.

Cut Here On

First PassCut Here

On Second

Pass

Figure 16. Incremental Cutting

22

www.SnapperPro.com

Image 24
Contents Briggs & Stratton Yard Power Products Group Model Number DescriptionNorth Main Street Munnsville, NYDate Purchased Table of Contents Operator Safety Operator SafetyOperating Safety Read the ManualSlope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Fuel and Maintenance Enclosed AreasTraining PreparationOperation Or warnings which must be followedTowed Equipment RIDE-ON Units EmissionsPeriods of exposure Do NotService and Maintenance Maintenance and StorageSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Safety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsFeatures and Controls Identification NumbersFeatures and Controls Seat Adjustment LeverIgnition Switch Control FunctionsFeatures & Controls General Operating Safety OperationOperation Checks Before StartingSeat Adjustment Mowing Height AdjustmentCheck Tire Pressures Tire PressureFoot Pedal Adjustment Raise and Lower the Roll BarInsert the key into the ignition switch and turn it to Starting the EngineStopping the Rider Pushing the Rider By HandZero Turn Driving Practice Smooth TravelForward Travel Practice Forward Reverse TravelPractice Turning Around a Corner Executing an End-Of-Row Zero TurnPractice Turning In Place Executing TurnsMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Attaching a Trailer Proper MulchingMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingRegular Maintenance Maintenance ScheduleSafety Items Before Every Spring Hours Fall Check Rider / Mower for loose hardwareRegular Maintenance Engine MaintenanceChecking / Adding Fuel Fuel FilterLubrication GreaseOil Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake AdjustmentReturn-To-Neutral Adjustment Deck Rod Timing Adjustment Deck Leveling AdjustmentRemove blocks from under the mower deck Mower Belt Replacement To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Battery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryRegular Maintenance Storage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting TroubleshootingTroubleshooting Chart Troubleshooting the RiderTroubleshooting the Mower Not driveTroubleshooting Troubleshooting Common Cutting ProblemsSpecifications DimensionsEngine ChassisFerris Limited Warranty Product Specifications Common Service Parts TractorMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.