Snapper S200KAV2561, S200XK2761 manual Check Hydraulic Oil Level, Change Hydraulic Oil Filter

Page 30

Maintenance

Regular Maintenance

Check Hydraulic Oil Level

1.Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris.

2.Unscrew the reservoir cap (B, Figure 24).

3.Look down the filler neck of the hydraulic oil reservoir

(A) and observe the oil level. When cold, the oil level should be approximately 4” (10 cm) below top of the filler neck.

4.If necessary, remove the reservoir cap (B) and add SAE 20W-50 motor oil.

5.Reinstall the reservoir cap.

Change Hydraulic Oil Filter

Change Interval: Every 250 Hours

Filter Part Number: 1719168

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. The manufacturer recommends this be a dealer-only service item.

1.Locate the transmission oil filter (B, Figure 25) at the rear of the battery compartment under the seat.

2.Lubricate the new filter base with a few drops of transmission oil. Fill the filter half full of oil.

3.Clean the area around the filter base and remove the filter. Do NOT drain the hydraulic system oil.

4.Thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

B

A

Figure 24. Checking Hydraulic Oil Level

A.Hydraulic Oil Reservoir

B.Reservoir Cap

A

B

Figure 25. Battery Compartment

A.Hydraulic Oil Reservoir

B.Hydraulic Oil Filter

28

www.SnapperPro.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents North Main Street Briggs & Stratton Yard Power Products GroupModel Number Description Munnsville, NYDate Purchased Table of Contents Operating Safety Operator SafetyOperator Safety Read the ManualSlope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Fuel and Maintenance Enclosed AreasOperation TrainingPreparation Or warnings which must be followedPeriods of exposure Towed Equipment RIDE-ON UnitsEmissions Do NotService and Maintenance Maintenance and StorageSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Safety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsFeatures and Controls Identification NumbersIgnition Switch Features and ControlsSeat Adjustment Lever Control FunctionsFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentMowing Height Adjustment Tire PressureFoot Pedal Adjustment Raise and Lower the Roll BarStopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Pushing the Rider By HandForward Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Reverse TravelPractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingSafety Items Before Every Spring Regular MaintenanceMaintenance Schedule Hours Fall Check Rider / Mower for loose hardwareChecking / Adding Fuel Regular MaintenanceEngine Maintenance Fuel FilterOil LubricationGrease Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake AdjustmentReturn-To-Neutral Adjustment Deck Rod Timing Adjustment Deck Leveling AdjustmentRemove blocks from under the mower deck Mower Belt Replacement To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Charging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryRegular Maintenance Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting Chart TroubleshootingTroubleshooting Troubleshooting the RiderTroubleshooting the Mower Not driveTroubleshooting Troubleshooting Common Cutting ProblemsEngine SpecificationsDimensions ChassisFerris Limited Warranty Product Specifications Common Service Parts TractorMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.
Top Page Image Contents