Snapper S200KAV2561, S200XK2761 manual Servicing The Mower Blades, Inspecting the Mower Blades

Page 31

Servicing The Mower Blades

Removing the Mower Blade

CAUTION

Avoid injury! Mower blades are sharp.

•Always wear gloves when handling mower blades or working near blades.

1.To remove the mower blade, use a 1” wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15/16” wrench (Figure 26).

2.If there are no flats on the spindle shaft, wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning.

Inspecting the Mower Blades

DANGER

Avoid injury! A worn or damaged blade can break, and a piece of the mower blade could be thrown into the operator’s or bystander’s area, resulting in serious personal injury or death.

•Inspect the mower blade every 25 hours or at least once a year.

•If the mower blade hits a solid object, stop the engine immediately and inspect the mower blade.

•Never weld or straighten bent mower blades.

1.Remove the mower blade from the unit. See Removing the Blade.

2.Inspect the mower blade (Figures 27 & 28). Discard the mower blade if it has any of the below conditions.

A.) Has more than .5” (12,7 mm) of the mower blade metal removed from previous sharpening or wear (D, Figure 27).

B.) The air lifts are excessively eroded (B & C, Figure

28) and the notch (C) is .25” (6,35 mm) deep or greater.

C.) Mower blade is bent or broken.

3.If the cutting edges are not sharp or have nicks, sharpen the blades. See Sharpening the Mower Blades.

Regular Maintenance

Figure 26. Loosening the Mower Blade for Removal

B

A

C

A

D

 

C

 

Figure 27. inspecting the Mower Blade Tips

A.Mower Blade Cutting Edge

B.Square Corner

C.Air Lift

D.Wear Measurement - DISCARD Mower Blade If greater than .5” (12,7 mm)

Maintenance

C

AB

Figure 28. inspecting the Mower Blade Air Lifts

A.New Mower Blade

B.Mower Blade at Wear Limit (A notch begins to form)

C.Mower Blade in Dangerous Condition (Notch measures .25” (6,35 mm) or greater DO NOT USE. Replace with new mower blade.)

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Munnsville, NY Briggs & Stratton Yard Power Products GroupModel Number Description North Main StreetDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetyThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Enclosed Areas Fuel and MaintenanceOr warnings which must be followed TrainingPreparation OperationDo Not Towed Equipment RIDE-ON UnitsEmissions Periods of exposureMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsControl Functions Features and ControlsSeat Adjustment Lever Ignition SwitchFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationTire Pressure Seat AdjustmentMowing Height Adjustment Check Tire PressuresRaise and Lower the Roll Bar Foot Pedal AdjustmentPushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderForward Reverse Travel Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting Turns Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Practice Turning In PlaceTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsHours Fall Check Rider / Mower for loose hardware Regular MaintenanceMaintenance Schedule Safety Items Before Every SpringFuel Filter Regular MaintenanceEngine Maintenance Checking / Adding FuelLubricating the Front Casters LubricationGrease OilChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentRemove blocks from under the mower deck To avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Jump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryRegular Maintenance Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartNot drive Troubleshooting the MowerTroubleshooting Common Cutting Problems TroubleshootingChassis SpecificationsDimensions EngineFerris Limited Warranty Tractor Product Specifications Common Service PartsMower Deck

S200KAV2561, S200XK2761 specifications

The Snapper S200KAV2561 and S200XK2761 are two standout models in the Snapper range of lawn care equipment, designed for homeowners seeking efficiency, durability, and user-friendly features. Both models embody the core values of the Snapper brand, which include innovative technology, superior performance, and ergonomic design.

The Snapper S200KAV2561 is equipped with a robust 25-horsepower engine, making it an ideal choice for tackling large lawns and challenging terrains. Its powerful engine is paired with a reliable automatic transmission, ensuring smooth operation while allowing the user to focus on the task at hand. This model features a wide 48-inch cutting deck, which enhances productivity and reduces mowing time by covering more ground in each pass. Additionally, the S200KAV2561 has a versatile height adjustment lever, enabling users to select from various cutting heights for a customized finish.

On the other hand, the Snapper S200XK2761 brings a new level of sophistication and efficiency with its 26-horsepower engine. This model also offers a robust hydrostatic transmission, providing effortless control and smooth acceleration without the need for manual gear shifting. The S200XK2761 features a 54-inch cutting deck, ensuring an impressive cutting width to tackle larger properties with ease. One of its standout technologies is the unique 2-in-1 mowing system that allows for both side discharge and mulch options, promoting efficient grass management and healthy lawn growth.

Both models demonstrate Snapper's commitment to user comfort and convenience. They come with an ergonomic seat design that offers cushioning and support for prolonged use, as well as easy-access controls that simplify operation. The durable construction of both models ensures longevity, with high-quality materials used throughout to withstand the rigors of regular lawn maintenance.

In terms of technology, both the S200KAV2561 and S200XK2761 boast fuel-efficient engines designed to minimize emissions while maximizing performance. Additionally, they incorporate Snapper's easy-start system, allowing users to begin their mowing tasks with minimal effort.

Overall, the Snapper S200KAV2561 and S200XK2761 offer a blend of power, precision, and ease of use that appeals to both novice and experienced homeowners. Whether you need professional-grade performance for a large property or a reliable mower for regular maintenance, either of these models will meet and exceed your expectations. With their excellent features and customer-centric designs, the Snapper S200 series is poised to enhance your lawn care experience.
Top Page Image Contents