Cub Cadet EX3200, EX2900 manual Machine, 17-2

Page 130

17. TROUBLESHOOTING

6

The engine

z Insufficient engine coolant

• Add engine coolant.

 

overheats.

 

 

 

 

• Check the radiator and the lines to and

 

 

 

from the radiator for leakage. If leakage is

 

 

 

found, contact your local Cub Cadet

 

 

 

Yanmar dealer for technical assistance.

 

 

z The engine is overloaded.

• Operate the tractor carefully. Avoid

 

 

 

overloading.

 

 

z Insufficiently tensioned fan belt

• Adjust the fan belt to the specified tension

 

 

 

value; or replace it.

 

 

z The radiator core is blocked.

• Eliminate the cause of blocking.

 

 

z Poor quality of engine coolant

• Possibly, sludge has accumulated on the

 

 

 

engine water jacket. Contact your local

 

 

 

Cub Cadet Yanmar dealer for technical

 

 

 

assistance.

2. Machine

 

Symptom

Cause

Remedy

1

The machine

z Engine speed is too low.

• Run the engine at a higher appropriate

 

excessively

 

speed.

 

vibrates.

 

 

 

z The Power Take Off (PTO) connecting

• Disconnect the Power Take Off (PTO)

 

 

the machine with the mounted

shaft, and reconnect it. Check if excessive

 

 

implement is not securely connected.

vibration reoccurs. If excessive vibration

 

 

 

persists, immediately stop operation and

 

 

 

contact your local Cub Cadet Yanmar

 

 

 

dealer for technical assistance.

 

 

z The engine throttle has not been

• Contact your local Cub Cadet Yanmar

 

 

correctly adjusted.

dealer for technical assistance.

2

Engine has

z Parking brake is in the engaged state.

• Disengage the parking brake.

 

successfully

 

 

 

z Insufficient transmission oil,

• Check the amount and quality of the oil.

 

started, but the

 

deteriorated transmission oil or

Replace deteriorated oil; refill as

 

machine fails to

 

clogged transmission filter

necessary. Check the filter for clogging,

 

operate.

 

 

and replace the clogged filter with a new

 

 

 

one.

 

 

z Transmission oil is too cold.

• Start the engine, and warm up. Only then,

 

 

 

operate the tractor.

3

3-point hitch does

z Insufficient transmission oil,

• Check the amount and quality of the oil.

 

not rise at all.

deteriorated transmission oil or

Replace deteriorated oil; refill as

 

 

clogged transmission filter

necessary. Check the filter for clogging,

 

 

 

and replace the clogged filter with a new

 

 

 

one.

 

 

z Transmission oil is too cold.

• Start the engine, and warm up.

 

 

z Excessively heavy implement on the 3-

• Use an implement of an acceptable

 

 

point hitch

weight.

4

3-point hitch

z Hydraulic pressure stop valve is in an

• Open the hydraulic pressure stop valve.

 

lowers too slowly.

insufficiently open position.

 

5

3-point hitch does

z Hydraulic pressure stop valve is in the

• Open the hydraulic pressure stop valve to

 

not lower at all.

closed position.

an appropriate position.

6

3-point hitch

z Hydraulic stop valve is in an

• Close the hydraulic pressure stop valve to

 

lowers too fast.

excessively open position.

an appropriate position.

Ex2900 / 3200 Operator's Manual

17-2

Page 129 Page 131
Image 130
Page 129 Page 131
Contents Page Page Welcome to the World of Cub Cadet Yanmar Tractor IntroductionEx2900 / 3200 Operator’s Manual Table of Contents Point Hitch and Drawbar 11-1 14-16 18-1 Safety Precautions About This ManualSafety Alert Symbol Precautions Before Operating Your Tractor Safe Practices for Operating Your Tractor Starting Your TractorConsiderations for Safety of Children Working with Your TractorOperating Your Tractor on Slopes Do notTraveling on a Road Safe Practices for Parking Your TractorOperating the Power Take Off PTO Using the 3-Point HitchSafe Practices for Servicing Your Tractor Safety Precautions Safety-Alert Symbol Understanding the Tractor Safety DecalsCare of DANGER, Warning and Caution Decals CY1A8160-85180 CY1A8160-85170CY1A8160-65321 CY1A8160-65370 CY1A8160-65310CY1A8160-65350 CY1A8160-65360CY1A8160-51520 CY1A8160-65300BCY1A7880-65620 CY124764-44810 CY198220-65621CY119629-77091 Servicing the Tractor Specifications Specifications TableTraveling Speeds Implement Capacities Implement Capacities Names and Functions of Components AppearanceOperator Station Controls Instrument Panel, Switches and Hand Controls Headlight / Turn Signal Switch Hazard Lights Button SwitchPre-Operation Check Precautions Before the OperationPRE-OPERATION Check Routine CheckOperating the Engine Starting the EngineSet the range shift lever to the Neutral position Pull the throttle control lever by 1/3 to 1/2 Stroke Depress the clutch pedalOn position Turn the starter key switch to the Start positionOFF position Start positionChecking the Lights on the Instrument Panel Starting the Engine in Cold Weather Important Avoid starter damageShutting Down the Engine Turn the range shift lever to the Neutral position Restarting a stalled EngineImportant Avoid engine damage Operating the Tractor Accident HazardOperating a New Tractor Changing the lubricating oil for the new tractorRaising and Lowering the Roll-Over Protective Structure Rops Raising Unfolding the Roll-Over Protective Structure Rops Adjust the operators position. Adjusting the Operators Seat Operation of the TractorTurn signals switch Fastening the Retractable Seat BeltStart the engine HeadlightsHazard Lights Select travel speed. Range Shift LeverWheel Drive Lever Raise the implement Disengage the parking brakeDrive Pedals Engaging the Cruise Control Disengaging the Cruise ControlStopping Travel of the Tractor Emergency Stop ProcedureAvoid injury Slow down before making a turn Engaging the Parking Brake Parking the TractorDisengaging the parking brake Engaging the Differential Lock Safe Practices for OperationDifferential Lock Disengaging the Differential LockSafely Driving the Tractor on Roads Pushing or Towing the Tractor Transporting the Tractor on a Trailer Operating on Slopes3013748 Uphill / Downhill About the Power SteeringSteep Downhill Power Take OFF PTO Be careful to avoid injuryNeutral position Installing an Implement to the Power Take Off PTO Drivelines Power Take OFF PTO Switch plunger Seat safety switch Prepare the Implement Being Mounted Point Hitch and DrawbarPoint Hitch 10-1Sway Links Using the 3-Point Hitch Adjusting the Right Lift LinkTop Link 10-2Maximum Allowable Load on the Drawbar Adjusting the DrawbarDrawbar 10-3Using the Safety Chain 10-4Point Hitch Control System Hydraulic System11-1 Hydraulic Flow Control / Stop Knob 11-2Implement Control Lever Controlling the Implement Control Valve11-3 Using the Hydraulic Lock Lever 11-4Connecting the Implement Hydraulic Hoses 11-5Tires TIRES, Wheels and Ballast12-1 Checking the Wheel Bolt Tightening Torque Wheel AdjustmentService Intervals Specified Torque12-3 Adjusting the Rear TreadTread Centerline Width Rear Wheels Front WheelsFront Ballast Front End Weights optionBallast 12-412-5 Maximum WeightUsing Liquid Weight for the Tires Avoid injuryMaintenance Check List Maintenance13-1 Lubricants 13-2Parts Replacement PartsTechnical Document 13-3Explosion Hazard Periodic ServiceWarranty and Repair of the Engine 14-1Opening the Hood Opening / Closing the Hood and Side PanelsOpening / Closing the Hood 14-2Opening / Closing the Side Panels Closing the Hood14-3 Checking the Engine Oil Level Daily Checks14-4 Inspecting the Transmission Oil Level 14-5Checking and Adjusting the Brake 14-6Checking the Radiator Hoses and Clamps Checking and Adjusting the Clutch14-7 14-8 Checking the Tire Air PressureTire pressures Cleaning the Radiator Cooling Fins Cleaning the Radiator Cooling Screen14-9 Checking the Fuel line Cleaning the Grille and Side ScreensChecking the Power Steering line Checking the Headlights, Hazard Lights, etcChecking the Cooling System 14-1114-12 Refilling the Fuel TankBio-diesel Fuels Inspection Procedure for Safety Interlock System 14-13Mid-Power Take Off PTO Engagement Lever Switch option Range Shift Lever Neutral Switch14-14 Seat Safety Switch Rear Power Take Off PTO Engagement Lever Switch14-15 First 50 Hours Checking the Front Axle Oil Level Grease SpecificationsEvery 50 Hours 14-17Extremely wet or muddy conditions Lubricating Grease Fittings on the Tractor14-18 All other conditionsLubricating the 3-Point Hitch Lubricating the Hydraulic Implement Control Valve LinkageLubricating the Seat Slide Rails 14-19Checking the Belt Tension Adjusting the Belt TensionServicing the Fan and Alternator Belt Replacing the BeltChecking the Fuel / Water Separator Checking the Battery Condition14-21 Servicing the Primary Air Filter Element Every 100 HoursServicing the Air Filter Element 14-22Servicing the Secondary Air Filter Element 14-2314-24 Changing the Engine Oil and Filter Every 200 HoursEngine Oil 14-25Checking the Air Intake Hoses and Clamps Inspecting and Adjusting the Toe-in14-26 Transmission Oil Illustration shows a Mid-Power Take Off PTO-typeEvery 300 Hours 14-2714-28 Changing the Front Axle Case Oil Every 500 HoursFront Axle Case Oil 14-29Replacing the Fuel Filter 14-30Draining the Cooling System Every 1000 HoursServicing the Cooling System 14-31Filling the Cooling System Flushing the Cooling System14-32 Checking the Fuel Injection Nozzle Adjusting the Engine Valve ClearanceRecommended Engine Coolant Checking the Fuel Injection PumpChanging Wheel Spacing and Tread Width General MaintenanceSelecting the Rotational Direction of Front Tires 14-34Special Note for the Battery Battery15-1 Servicing the Battery Safely 15-2Removing the Battery Inspecting the BatteryRemoving and Installing the Battery 15-3Cleaning the Battery and Terminals Installing the Battery15-4 Using a Booster Battery 15-5Checking the Alternator Fuse and the Main Fuse Replacing the Accessory FusesFuses 15-615-7 BulbReplacing the Headlight Bulb Avoid personal injuryReplacing the Tail Light Bulb Replacing the Turn Signal / Hazard Lights Bulb15-8 Replacing the Instrument Panel Light Bulb Adjusting the HeadlightsHeadlights 15-9Preparing the Machine for Storage StorageSafe Practices for Storage 16-116-2 Preparing the Fuel and Engine for StorageEngine Important Be very careful to avoid damagePreparing the Stored Tractor for Operation 16-3How to Use the Troubleshooting Table Troubleshooting17-1 Machine 17-2Steering Brake17-3 Index 18-1
Related manuals
Manual 3 pages 8.69 Kb

EX2900, EX3200 specifications

The Cub Cadet EX2900 and EX3200 models represent a top tier of sub-compact tractors, designed to meet the diverse needs of homeowners and landscape professionals. Renowned for their reliability and performance, these tractors are equipped with robust features and advanced technologies.

At the heart of the EX2900 and EX3200 is a powerful, fuel-efficient engine. The EX2900 boasts a 29 horsepower engine, while the EX3200 takes it up a notch with a 32 horsepower variant. Both engines feature a liquid cooling system, ensuring optimal performance even under heavy loads. This added power allows for efficient operation of various implements such as loaders, mowers, and tillers, making them ideal for a range of tasks from mowing lawns to landscaping and agricultural duties.

One of the standout characteristics of these models is their hydrostatic transmission. This allows for smooth, effortless speed control and direction changes without the need for manual gear shifting. Operators appreciate the ease of use, especially when navigating tight spaces or performing multiple tasks in quick succession.

Comfort and convenience are also prominent in the design of the EX2900 and EX3200. The spacious operator station features an ergonomic seat with ample legroom, providing comfort during long hours of operation. Easy-to-reach controls and a dashboard with clear indicators enhance usability, making tasks simpler and more efficient.

In addition to power and comfort, these tractors emphasize versatility. A quick-attach loader system allows users to switch out attachments swiftly, adapting to a variety of chores. The three-point hitch increases compatibility with various implements, giving owners the flexibility to tackle different jobs with ease.

Cub Cadet has integrated advanced technology into the EX2900 and EX3200 models to enhance performance further. A 12-volt electrical system provides reliable starting power, while the LED headlights improve visibility during early morning or evening operations. Safety features such as an ROPS (Roll-Over Protective Structure) add an additional layer of protection for operators.

Overall, the Cub Cadet EX2900 and EX3200 tractors combine power, comfort, and versatility, making them ideal choices for homeowners and professionals alike. With their dependable performance and user-friendly features, these models are built to tackle everything from simple yard maintenance to more demanding agricultural tasks, delivering quality and reliability in every job.
Top Page Image Contents