Campbell Hausfeld Maintenance, PW2725, PW3230, PW4035, Operation Continued

Page 9
never pull the starter rope on the engine when the spark plug is

PW2725, PW3230, PW4035

Operation (Continued)

never pull the starter rope on the engine when the spark plug is

removed unless the spark plug hole is covered. Fuel vapor from the hole can ignite by a spark.

7.Place a rag over the spark plug hole and slowly pull the starter rope several times to distribute the oil..

Winterizing instructions

1..Follow and complete the Long Term Storage Instructions above..

2.Disconnect the spark plug wire..

3.Disconnect the high pressure hose from the pump..

4.Insert a 12 in.. to 14 in.. piece of garden hose into the pump inlet..

5.Place a funnel in the other end of the garden hose..

read the manufacturer’s

instructions for safe handling and disposal of RV antifreeze.

6.Pour approximately 6 oz. of RV antifreeze into the funnel..

7.Pull the starter rope several times until the RV antifreeze comes out of the pump outlet..

8.Disconnect the high pressure hose from the gun and drain the hose.. Hold the gun and lance in a vertical position and squeeze the trigger to drain the water out..

tips for extending the life of your pressure washer

1.Never operate the unit without water..

2..Your pressure washer is not meant to pump hot water.. Never connect your pressure washer to a hot water supply as it will significantly reduce the life of the pump..

3..Running the unit for more than one minute without spraying water causes heat to build up in the pump.. Running the unit without spraying water can damage pump components..

Maintenance

Observe regular maintenance intervals

to ensure maximum performance and

life from the pressure washer.. Refer to the schedule for recommended maintenance.. If you operate the pressure washer in dusty conditions, perform maintenance checks more often..

engine Oil changing instructions

before tipping the engine or

equipment to drain oil, drain fuel from the fuel tank.

Note: Change oil while the engine is

1..Disconnect the spark plug wire from the spark plug..

2.Locate and remove the engine oil drain plug (See Figure 15)..

Oil Fill

Oil Drain

3.. Drain old oil..

4.Replace the drain plug and set the unit upright..

5.Refill the unit with new oil of a recommended type and quantity.. Fill the unit to the bottom edge of the oil fill neck..

pump Oil checking/ changing instructions

Please refer to provided AR Pump Specification page provided with your Pressure Washer for details..

cool..

Figure 15 - Oil drain and fill locations

9

www.chpower.com

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents PW2725, PW3230, PW4035 Operating Instructions and Parts ManualGasoline Powered ContentsOperating Instructions and Parts Manual Frequently Asked QuestionsGetting To Know Your Pressure Washer PW2725, PW3230, PW4035Safety Guidelines Safety and Warning InformationImportant Safety Instructions This product or its power cordAssembly Pre-OperationKeep hose away from sharp UnpackingOperation Pre-Operation ContinuedTrigger safety latch 1. Surface PreparationAngle to the cleaning surface Operation ContinuedHow to avoid damaging surfaces Pressure Adjustment5. Cleaning Power General Cleaning Tips7. Pressure Relief Procedure 4. Detergent Applicationnever pull the starter rope on the engine when the spark plug is MaintenanceWinterizing instructions read the manufacturer’sMaintenance Continued Service RecordMaintenance Schedule Maintenance ScheduleReplacement Parts List For replacement parts or technical assistance, CallReplacement Parts List DescriptionD VERSION Ø 1 inch D VERSION Ø 3/4 inchTYPE F25 TYPE F40Part Number REPLACEMENT PARTS KITSSymptom Troubleshooting Chart - Gasoline Powered Pressure Washers OnlyPossible Causes Corrective ActionPump noisy / pump runs Limited Warranty Lavadoras a presión Manuel de Instrucciones y Lista de Piezascon motor a gasolina ÍndicePreguntas Frecuentes Manuel de Instrucciones y Lista de Piezas19 Sp Conozca su Lavadora a PresiónGuías de seguridad Advertencias e Información de SeguridadInstrucciones de seguridad importantes Peligro indica una situaciónEnsamblaje y Previo al Funcionamiento Advertencias e Información de Seguridad ContinuaciónMantenga la manguera DESEMPAQUEFuncionamiento Ensamblaje y Previo al Funcionamiento ContinuaciónSeguro del gatillo 1. Preparación de la superficieCuando hale del cordón de Funcionamiento Continuaciónno deje nunca que el condón de arranque se devuelva solo. El hacerlo así puede trabar el sistema de retroceso8. Apagado 4. Aplicación de detergenteDETERGENTES Nuncanunca hale del cordón de MantenimientoInstrucciones para la preparación invernal lea las instruccionesMantenimiento Continuación Registro de ServicioPrograma de mantenimiento Programa deLista de Repuestos Para Ordenar Repuestos o Asistencia Técnica, Llame al TeléfonoPW4035 Lista de Partes de ReparaciónJuego de Juego delsello del anillos paraRepuesto Número delJUEGOS DE PIEZAS DE REPUESTO 29 Sp30 Sp Asegúrese de que las mangueras y los empalmes noReemplace los sellos de aceite o los anillos-O.. Consulte al 31 Sp NotasLas válvulas están sucias, gastadas o 1. La bomba succiona aire/suministro32 Sp Garantía Limitada
Top Page Image Contents