DeVillbiss Air Power Company A16064, DVH2600 Pressure Washer Terminology, Pressure Adjustments

Page 10

BASIC ELEMENTS OF AN ENGINE

Refer to the engine manual for location and operation of engine controls.

Choke Control: Opens and closes carburetor choke valve.

Starter Grip: Pulling starter grip operates recoil starter to crank engine.

Engine Switch: Enables and disables ignition system.

PRESSURE WASHER

TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI. GPM x PSI = CU

Bypass Mode: Allows water to re-circulate within pump when the gun trigger is not pulled.

Allowing the unit to run for more than

two minutes without the gun trigger pulled could cause overheating and damage to the pump.

Chemical Injection System: Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods.

1.Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Change to the 40º nozzle - (white) this nozzle delivers a less powerful stream of water and a wider spray pattern.

DO NOT attempt to increase pump

pressure. A higher pressure setting than the factory set pressure may damage pump.

SPRAY WAND NOZZLES

The nozzles for the spray wand are stored in the nozzle holder on the panel assembly. Colors on the panel identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the job to be performed.

CHANGING NOZZLES ON SPRAY WAND

Risk of fluid injection. Do not

direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur.

Flying objects could cause risk

of serious injury. Do not attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles.

1.Pull quick- connect coupler back and insert nozzle.

2.Release quick- connect coupler

and twist nozzle to make sure it is secure in coupler.

Flying object could cause risk of serious

injury. Ensure nozzle is completely inserted in quick-connect socket and quick-connect snap ring is fully engaged (forward) before squeezing gun trigger.

A16064

10- ENG

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Table of Contents Important Safety Instructions Safety Guidelines DefinitionsConsumer Safety Information Risk of Explosion or Fire What can Happen HOW to Prevent ITFaces such as houses, automobiles Operating the pressure washer in anMinimum of 4 1.2 m away from sur Or live plants that could be damagedDo not allow hose to contact muffler Risk of Injury from Spray What can Happen HOW to Prevent ITInjection injuries. do not Treat Injuries can result if system pressureCausing serious hand and arm injury Risk of Unsafe Operation What can Happen HOW to Prevent ITControls of the pressure washer What can Happen HOW to Prevent IT Risk of Bursting What can Happen HOW to Prevent ITRisk of HOT Surfaces Risk of Chemical Burn What can Happen HOW to Prevent IT SpecificationsRisk of Electrical Shock What can Happen HOW to Prevent IT Carton Contents Assembly InstructionsBasic Elements of a Pressure Washer Operating InstructionsRisk of bursting. Use a tire pressure Spray Wand Nozzles Pressure AdjustmentsPressure Washer Terminology Changing Nozzles on Spray WandTo Apply chemicals Press chemical HOW to Apply CHEMICALS/CLEANING SolventsHose onto Area add fresh, high quality StartingA well ventilated outdoor Check engine oil level. SeeShutting Down To reduce the possibilityNozzle Cleaning MaintenanceHOW to Clean the Water Inlet Filter EnginePressure Washer StorageEngine Pump If space is needed, remove handles and replace as shownTrouble Shooting Guide Problème Cause CorrectionAccessories Repairs Limited Warranty Responsibility of Original Purchaser Initial UserTable des matières Questions ?Renseignements SUR LA Sécurité DU Consommateur Mesures DE Sécurité DéfinitionsMesures DE Sécurité Importantes Ne pas vaporiser des liquides Pression dans une zone avec arbustesSurfaces peintes, faire fondre tout InflammablesUne personne ou des animaux Le jet d’eau EST sous haute pression etNe jamais diriger la lance ou le jet vers Toujours fixer solidement le verrou deGarder la laveuse haute pression hors de Risque D’ÉCLATEMENT Des pneus surgonflés pourraientSeule personne. Demander de l’aide Débrancher tout produit fonctionnantModèle ’ASSEMBLAGE Contenu DE LA BoîteAttachez la lance au pistolet et bien serrer Utilisation Éléments DE Base D’UNE Laveuse À PressionUtilisation DE LA Lance DE Vaporisation Éléments DE Base DU MoteurTerminologie DES Laveuses À Pression Changement de buse de la lance de vaporisationApplication DES Produits CHIMIQUES/SOLVANTS DE Nettoyage Dans lorifice Dentrée deau De la pompe DémarrageQue lécran filtrant est Le côté conique doit être dirigé versAttachez le boyau à haute pression à la sortie de la pompe Arrêt DE LappareilRelâchez la détente pour arrêter le débit d’eau Moteur EntretienNettoyage DU Filtre ’ENTRÉE D’EAU PompePrendre un entonnoir de 170 ml EntreposagePompe Po avec un connecteur mâle à une extrémitéProblème Cause Correction Guide DE DépannageAucun carburant Réparations AccessoiresProblème Garantie Limitée Garantie Limitée D’UN 1 AN SUR LES Composants DU ProduitContenido Pieza No. A16064 Rev 3/9/06Información DE Seguridad Para EL Consumidor Definiciones DE Normas DE SeguridadInstrucciones Importantes DE Seguridad Riesgo Respiratorio Asfixia Riesgo DE Explosión O Incendio Continuar¿QUÉ Puede SUCEDER? Cómo Evitarlo Riesgo DE Lesión POR Pulverización Riesgo DE Lesión POR Pulverización Continuar Riesgo DE DE Estallido Riesgo DE Superficies CalientesRiesgo DE Quemadura Química LEA Y Conserve Estas InstruccionesBusque todas las partes sueltas de la caja y retírelas Contenido DE LA CajaInstrucciones Para Armar Coloque los paneles en posición horizontalElementos Básicos DE UNA Lavadora a Presión Instrucciones DE OperaciónMotor Acciona la bomba de alta presión Terminología DE LA Lavadora a Presión Elementos Básicos DEL MotorCaracterísticas DE Operación DE LA Lavadora a Presión Cómo Emplear Productos Químicos Y Solventes Para Limpieza Arranque Verifique el nivel de aceiteAcción contraria podría dañar la bomba ApagadoConecte la manguera de alta presión a la salida de la bomba Corte el suministro del aguaCómo Limpiar EL Filtro DE Entrada DEL Agua MantenimientoMotor BombaLavadora a Presión Causa Guía DE Diagnóstico DE ProblemasProblema CorrecciónProblema Causa Corrección AccesoriosReparaciones Garantía Limitada Responsabilidad DEL Comprador Original usuario inicialMERIDA, YUC CULIACAN, SINMEXICO, D.F MONTERREY, N.LA16064

DVH2600, A16064 specifications

DeVillbiss Air Power Company is renowned for its commitment to delivering high-quality air-powered tools and equipment, with the A16064 and DVH2600 models exemplifying this dedication. These models stand out in their respective categories, showcasing advanced technologies and features designed for both professional and amateur users.

The DeVillbiss A16064 is a versatile air compressor characterized by its robust design and powerful performance. It is ideal for automotive applications, offering a reliable air source for inflating tires, powering pneumatic tools, and servicing vehicles. It features an efficient motor for quick start-up and operation, ensuring that users can tackle tasks with minimal downtime. The A16064 utilizes a high-capacity air tank to provide a consistent airflow, delivering the pressure needed to handle various applications seamlessly. Additionally, its lightweight construction makes it portable, allowing users to transport it effortlessly around job sites or garages.

On the other hand, the DVH2600 is a top-tier air-powered tool highlighting the latest advancements in technology to enhance user experience and efficiency. This model is designed for paint spraying, featuring an advanced spray system that ensures an even coat with minimal overspray. It boasts variable pressure controls, allowing users to adjust the air pressure for different applications, ensuring that they achieve the desired finish every time. The DVH2600 is also equipped with an ergonomic handle and lightweight body, promoting ease of use during extended periods of operation.

Both models incorporate durable components designed for longevity, providing users with peace of mind about their investment. Their compact designs ensure that they can fit into tight spaces, making them suitable for a variety of tasks, from home improvement projects to professional applications.

In summary, the DeVillbiss A16064 and DVH2600 are outstanding examples of air power technology, embodying the brand's commitment to quality and performance. Their innovative features, user-friendly designs, and dependable capabilities make them essential tools for anyone looking to harness the power of compressed air effectively. Whether for professional use or hobbyist pursuits, these models promise to deliver exceptional results and reliability.
Top Page Image Contents