Briggs & Stratton 020274-0 manual Connect Hose and Water Supply to Pump

Page 10

Connect Hose and Water Supply to Pump

NOTICE

DO NOT run the pump without the water supply connected and turned on.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE: Remove and discard the shipping caps from the pump’s high pressure outlet and water inlet before attaching hoses.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun. Tighten by hand.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER connect high pressure hose to nozzle extension.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•Always be certain spray gun, nozzles and accessories are correctly attached.

2.Attach other end of high pressure hose to high pressure outlet on pump. Tighten by hand.

3.Before connecting garden hose to water inlet, inspect inlet screen (A). Clean screen if it contains debris or have it replaced if damaged. DO NOT run pressure washer if inlet screen is damaged.

A

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect the garden hose (not to exceed 50 feet in length) to the water inlet. Tighten by hand.

NOTICE

Damage to pump or water inlet connector will occur if a One Way Valve (vacuum breaker or check valve) is connected to pump.

•There MUST be at least ten feet (3M) of unrestricted garden hose between the pressure washer inlet and any device, such as a One Way Valve.

•Damage to equipment caused by attaching a One Way Valve to pump will void warranty.

6.Turn ON the water, press red button (B) on the gun and squeeze the trigger to purge the pump system of air and impurities.

B

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

•Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate safety goggles.

•NEVER substitute safety glasses for safety goggles.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all of the following.

1.Be sure to read the Operator Safety section and How to Use Your Pressure Washer in Operation section before using pressure washer.

2.Make sure handle is in place and secure.

3.Check that oil has been added to proper level in the engine crankcase.

4.Add proper fuel to fuel tank.

5.Check for properly tightened hose connections.

6.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

7.Provide a proper water supply at an adequate flow.

10

BRIGGSandSTRATTON.COM

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Engine Where to Find UsPressure Washer Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionCertain components in this product and related Operate pressure washer only outdoorsContact with muffler area can result in serious burns Broken bones, fractures, bruises, or sprains could resultUnintentional sparking can result in fire or electric shock Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassUnpack Pressure Washer AssemblyAttach Handle and Accessory Tray Items in the carton includeFuel must meet these requirements Add Engine OilAdd Fuel High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpFeatures and Controls Oil Drain Drain engine oil herePressure Washer Location OperationClearances and Air Movement How to Start Your Pressure Washer How to Stop Your Pressure Washer Lever to Choke position, then to Run positionHow to Use ProjectPro Nozzles How to Use Accessory TrayFollow these instructions to change ProjectPro nozzles Usage Tips Cleaning and Applying DetergentTo apply detergent, follow these steps Automatic Cool Down System Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing For RinsingMaintenance Schedule MaintenancePressure Washer Maintenance Check High Pressure Hose Nozzle MaintenanceRing Maintenance Check Detergent Siphoning TubeChecking Oil Level Engine MaintenanceOil Oil Recommendations Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Install spark plug and tighten firmlyAir Cooling System After Each UseKeep areas within heavy line clear of debris Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionOwner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Common Service Parts Product Specifications800 Manual del Operario Motor Dónde encontrarnosLimpiadora a Presión Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de Operario Características y mandos OperandoReglas de seguridad Seguridad de OperarioDerscripción del equipo Símbolos de Peligro y SignificadosAdvertencia Riesgo de electrocuciónCuando Pruebe LA Bujía DEL Motor Aviso Conecte el manubrio y bandeja accesoria MontajeDesembale la limpiadora a presión Los artículos que se encuentran en la caja sonEl combustible debe reunir los siguientes requisitos Agregar aceite al motorAgregue combustible Gran altitudLista de revision previa al arranque del motor Conecte la manguera y el suministro de agua a la bombaProporcione el suministro de agua adecuado Características y mandos Usar cuatro boquillas diferentesCómo darle arranque a su máquina limpiadora a presión OperandoUbicación del limpiadora a presión Espacio libre alrededor del limpiadora a presiónAhogado Choke Cuando arranque el motor, mueva lentamente la Cómo detener su máquina limpiadora a presiónRepite los pasos 11 por La Presión Baja Utilización de la bandeja de accesoriosCómo usar las boquillas ProjectPro La Presión AltaUso inclina Limpieza y aplicación del detergenteElija la boquilla ProjectPro que desee Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Enjuage de la máquina limpiadora a presiónLimpieza del tubo de inyección de detergente Para EnjuagePlan de mantenimiento MantenimientoMantenimiento de la limpiadora a presión Chequee el tubo de sifón del detergente Revise y limpie el colador de entradaRevise la manguera de alta presión Revise la pistola y la extensión para boquillasAceite Recomendaciones sobre el aceite Mantenimiento del motorMantenimiento de los anillos o Comprobación del nivel de aceiteServicio del depurador de aire Cambio de aceite del motorAsegúrese de que la unidad esté en una superficie plana Servicio del bujíaServicio del apagachispas Despues de cada usoSistema de refrigeración de aire Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónGarantía del sistema de control de emisiones Responsabilidades de la garantía del propietarioInformación sobre emisiones Garantía Limitada Servicio común despide Especificaciones del productoTemperatura del suministro

020274-0 specifications

Briggs & Stratton 020274-0 is a highly regarded portable generator that provides reliable power solutions for a variety of applications, including recreational activities, job sites, and emergency backup needs. This generator is known for its robustness, efficiency, and user-friendly design, making it a go-to choice for many consumers.

One of the key features of the Briggs & Stratton 020274-0 is its powerful engine. Equipped with a reliable 210cc OHV engine, it delivers a peak power output of 3,300 watts and a running power of 2,650 watts. This capacity is sufficient for running essential household appliances during power outages or providing energy for tools and equipment on job sites. The generator offers both 120V and 120/240V outlets, ensuring versatility for various applications.

Another notable characteristic of this generator is its lightweight and compact design. Weighing in at approximately 68 pounds, it is relatively easy to transport and maneuver, thanks to its integrated handle and rugged wheels. This portability feature is essential for users who need to move the generator between locations frequently.

The Briggs & Stratton 020274-0 also incorporates advanced technologies aimed at enhancing efficiency and performance. The generator utilizes a surge protection feature that safeguards connected devices from power surges, ensuring their longevity and reliability. Additionally, it features an automatic idle control system that reduces fuel consumption by lowering engine speed when not in use, thereby extending the runtime and minimizing operational costs.

The generator is designed with user convenience in mind. The control panel is intuitively laid out, providing easy access to power outlets and switches. The fuel tank has a generous capacity of 1.5 gallons, offering a runtime of up to 9 hours at a 25% load, making it ideal for longer use without the need for frequent refueling.

Moreover, the Briggs & Stratton 020274-0 comes with a range of safety features, including a low-oil shutdown system that prevents engine damage by automatically shutting off the generator when oil levels fall below a safe threshold. This feature extends the life of the generator and ensures dependable performance over time.

In summary, the Briggs & Stratton 020274-0 portable generator stands out with its powerful performance, user-friendly features, and advanced technologies. Its reliability, ease of use, and safety mechanisms make it an excellent choice for both home and professional use, delivering peace of mind when you need power the most.
Top Page Image Contents