Briggs & Stratton 020274-0 manual Add Engine Oil, Add Fuel, Fuel must meet these requirements

Page 9

Add Engine Oil

1.Place pressure washer on a flat, level surface.

2.Clean area around oil fill and remove yellow oil fill cap .

3.Using oil funnel (optional), slowly pour contents of provided oil bottle into oil fill opening.

NOTICE

Improper treatment of pressure washer can damage it and shorten its life.

•DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil. This may result in an engine failure.

4.Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

•A minimum of 87 octane/87 AKI (91 RON). High altitude use, see High Altitude.

•Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel recommendations voids warranty.

•DO NOT use unapproved gasoline such as E85.

•DO NOT mix oil in gasoline.

•DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel. See Storage. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands. This engine is certified to operate on gasoline. The emission control system for this engine is EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn pressure washer OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

•Fill fuel tank outdoors.

•DO NOT overfill tank. Allow space for fuel expansion.

•If fuel spills, wait until it evaporates before starting engine.

•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

•DO NOT light a cigarette or smoke.

1.Clean area around fuel fill cap, remove cap.

2.Slowly add regular unleaded fuel (A) to fuel tank (B). Be careful not to overfill. Allow about 1.5" (4 cm) (C) of tank space for fuel expansion.

B

C

A

3.Install fuel cap and let any spilled fuel evaporate before starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To remain emissions compliant, high altitude adjustment is required. Operation without this adjustment will cause decreased performance, increased fuel consumption, and increased emissions. See an Authorized Briggs & Stratton dealer for high altitude adjustment information. Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude kit is not recommended.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator’s Manual Pressure Washer Where to Find UsEngine Date PurchasedTable of Contents Safety Rules Operator SafetyHazard Symbols and Meanings Equipment DescriptionOperate pressure washer only outdoors Certain components in this product and relatedBroken bones, fractures, bruises, or sprains could result Contact with muffler area can result in serious burnsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Risk of eye injury Spray can splash back or propel objectsAttach Handle and Accessory Tray AssemblyUnpack Pressure Washer Items in the carton includeAdd Fuel Add Engine OilFuel must meet these requirements High AltitudeConnect Hose and Water Supply to Pump Checklist Before Starting EngineOil Drain Drain engine oil here Features and ControlsOperation Pressure Washer LocationClearances and Air Movement How to Start Your Pressure Washer Lever to Choke position, then to Run position How to Stop Your Pressure WasherHow to Use Accessory Tray How to Use ProjectPro NozzlesFollow these instructions to change ProjectPro nozzles Cleaning and Applying Detergent Usage TipsTo apply detergent, follow these steps Pressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief For RinsingMaintenance Maintenance SchedulePressure Washer Maintenance Ring Maintenance Nozzle MaintenanceCheck High Pressure Hose Check Detergent Siphoning TubeOil Oil Recommendations Engine MaintenanceChecking Oil Level Adding Engine OilTo service the air cleaner, follow these steps Service Air CleanerService Spark Plug Install spark plug and tighten firmlyAfter Each Use Air Cooling SystemKeep areas within heavy line clear of debris Long Term Storage Winter StorageProblem Cause Correction TroubleshootingEmissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Product Specifications Common Service Parts800 Manual del Operario Limpiadora a Presión Dónde encontrarnosMotor Fecha de compraSeguridad de Operario Resolución de problemas GarantíasMontaje Características y mandos OperandoDerscripción del equipo Seguridad de OperarioReglas de seguridad Símbolos de Peligro y SignificadosRiesgo de electrocución AdvertenciaCuando Pruebe LA Bujía DEL Motor Aviso Desembale la limpiadora a presión MontajeConecte el manubrio y bandeja accesoria Los artículos que se encuentran en la caja sonAgregue combustible Agregar aceite al motorEl combustible debe reunir los siguientes requisitos Gran altitudConecte la manguera y el suministro de agua a la bomba Lista de revision previa al arranque del motorProporcione el suministro de agua adecuado Usar cuatro boquillas diferentes Características y mandosUbicación del limpiadora a presión OperandoCómo darle arranque a su máquina limpiadora a presión Espacio libre alrededor del limpiadora a presiónAhogado Choke Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laRepite los pasos 11 por Cómo usar las boquillas ProjectPro Utilización de la bandeja de accesoriosLa Presión Baja La Presión AltaElija la boquilla ProjectPro que desee Limpieza y aplicación del detergenteUso inclina Para aplicar el detergente, siga los siguientes pasosLimpieza del tubo de inyección de detergente Enjuage de la máquina limpiadora a presiónSistema de enfriamiento automático alivio térmico Para EnjuageMantenimiento Plan de mantenimientoMantenimiento de la limpiadora a presión Revise la manguera de alta presión Revise y limpie el colador de entradaChequee el tubo de sifón del detergente Revise la pistola y la extensión para boquillasMantenimiento de los anillos o Mantenimiento del motorAceite Recomendaciones sobre el aceite Comprobación del nivel de aceiteAsegúrese de que la unidad esté en una superficie plana Cambio de aceite del motorServicio del depurador de aire Servicio del bujíaDespues de cada uso Servicio del apagachispasSistema de refrigeración de aire Almacenamiento prolongado Almacenamiento para inviernoProblema Causa Solución Resolución de problemasResponsabilidades de la garantía del propietario Garantía del sistema de control de emisionesInformación sobre emisiones Garantía Limitada Especificaciones del producto Servicio común despideTemperatura del suministro

020274-0 specifications

Briggs & Stratton 020274-0 is a highly regarded portable generator that provides reliable power solutions for a variety of applications, including recreational activities, job sites, and emergency backup needs. This generator is known for its robustness, efficiency, and user-friendly design, making it a go-to choice for many consumers.

One of the key features of the Briggs & Stratton 020274-0 is its powerful engine. Equipped with a reliable 210cc OHV engine, it delivers a peak power output of 3,300 watts and a running power of 2,650 watts. This capacity is sufficient for running essential household appliances during power outages or providing energy for tools and equipment on job sites. The generator offers both 120V and 120/240V outlets, ensuring versatility for various applications.

Another notable characteristic of this generator is its lightweight and compact design. Weighing in at approximately 68 pounds, it is relatively easy to transport and maneuver, thanks to its integrated handle and rugged wheels. This portability feature is essential for users who need to move the generator between locations frequently.

The Briggs & Stratton 020274-0 also incorporates advanced technologies aimed at enhancing efficiency and performance. The generator utilizes a surge protection feature that safeguards connected devices from power surges, ensuring their longevity and reliability. Additionally, it features an automatic idle control system that reduces fuel consumption by lowering engine speed when not in use, thereby extending the runtime and minimizing operational costs.

The generator is designed with user convenience in mind. The control panel is intuitively laid out, providing easy access to power outlets and switches. The fuel tank has a generous capacity of 1.5 gallons, offering a runtime of up to 9 hours at a 25% load, making it ideal for longer use without the need for frequent refueling.

Moreover, the Briggs & Stratton 020274-0 comes with a range of safety features, including a low-oil shutdown system that prevents engine damage by automatically shutting off the generator when oil levels fall below a safe threshold. This feature extends the life of the generator and ensures dependable performance over time.

In summary, the Briggs & Stratton 020274-0 portable generator stands out with its powerful performance, user-friendly features, and advanced technologies. Its reliability, ease of use, and safety mechanisms make it an excellent choice for both home and professional use, delivering peace of mind when you need power the most.
Top Page Image Contents