Briggs & Stratton 020364-0 manual Add Engine Oil, Add Fuel, Fuel must meet these requirements

Page 10

Add Engine Oil

1.Place pressure washer on a flat, level surface.

2.Clean area around oil fill and remove yellow oil fill cap .

3.Using oil funnel (optional), slowly pour contents of provided oil bottle into oil fill opening.

NOTICE

Improper treatment of pressure washer can damage it and shorten its life.

•DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil. This may result in an engine failure.

4.Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

•A minimum of 87 octane/87 AKI (91 RON). High altitude use, see High Altitude.

•Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel recommendations voids warranty.

•DO NOT use unapproved gasoline such as E85.

•DO NOT mix oil in gasoline.

•DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel. See Storage. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands. This engine is certified to operate on gasoline. The emission control system for this engine is EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn pressure washer OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

•Fill fuel tank outdoors.

•DO NOT overfill tank. Allow space for fuel expansion.

•If fuel spills, wait until it evaporates before starting engine.

•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

•DO NOT light a cigarette or smoke.

1.Clean area around fuel fill cap, remove cap.

2.Slowly add regular unleaded fuel (A) to fuel tank (B). Be careful not to overfill. Allow about 1.5" (4 cm) (C) of tank space for fuel expansion.

B

C

A

3.Install fuel cap and let any spilled fuel evaporate before starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To remain emissions compliant, high altitude adjustment is required. Operation without this adjustment will cause decreased performance, increased fuel consumption, and increased emissions. See an Authorized Briggs & Stratton dealer for high altitude adjustment information. Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude kit is not recommended.

10

BRIGGSandSTRATTON.COM

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Engine Where to Find UsPressure Washer Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionWhen Adding or Draining Fuel Contact with muffler area can result in serious burns Broken bones, fractures, bruises, or sprains could resultUnintentional sparking can result in fire or electric shock Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassUnpack Pressure Washer AssemblyAttach Handle and Accessory Tray Items in the carton includeAttach Hose Reel Fuel must meet these requirements Add Engine OilAdd Fuel High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpWater Inlet Connection for garden hose Features and ControlsOil Drain Drain engine oil here Pump Develops high pressure Pressure Washer Location OperationClearances and Air Movement How to Start Your Pressure Washer Attach nozzle extension to spray gun. Tighten by handEngage trigger lock on spray gun when not in use How to Stop Your Pressure WasherLever to Choke position, then to Run position How to Use Project Pro Nozzles How to Use Accessory TrayFollow these instructions to change Project Pro nozzles Usage Tips Cleaning and Applying DetergentTo apply detergent, follow these steps Automatic Cool Down System Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing For RinsingMaintenance Schedule MaintenancePressure Washer Maintenance Check High Pressure Hoses Nozzle MaintenanceRing Maintenance Check Detergent Siphoning TubeChecking Oil Level Engine MaintenanceOil Oil Recommendations Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Spark Arrester ServiceAfter Each Use Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionOwner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Page Common Service Parts Product Specifications800 Manual del Operario Motor Dónde encontrarnosLimpiadora a Presión Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de Operario Características y mandos OperandoDerscripción del Equipo Seguridad de OperarioReglas de seguridad Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Conecte el asa y bandeja accesoria MontajeDesembale la limpiadora a presión Los artículos que se encuentran en la caja sonFije el carrete de manguera El combustible debe reunir los siguientes requisitos Agregar aceite al motorAgregue combustible Gran altitudLista de revision previa al arranque del motor Conecte la manguera y el suministro de agua a la bombaProporcione el suministro de agua adecuado Características y mandos Bomba Desarrolla alta presión de aguaUbicación del limpiadora a presión OperandoPresión Cómo darle arranque a su máquina limpiadora aAdvertencia Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laLa Presión Baja Utilización de la bandeja de accesoriosCómo usar las boquillas Project Pro La Presión AltaUso inclina Limpieza y aplicación del detergenteElija la boquilla Project Pro que desee Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Enjuage de la máquina limpiadora a presiónLimpieza del tubo de inyección de detergente Para EnjuagePlan de mantenimiento MantenimientoMantenimiento de la limpiadora a presión Chequee el tubo de sifón del detergente Revise y limpie el colador de entradaCompruebe las mangueras de alta presión Revise la pistolaMantenimiento del motor Suministre servicio al depurador de aire una vez cada Asegúrese de que la unidad esté en una superficie planaServicio del depurador de aire Servicio del bujíaSistema de refrigeración de aire Despues de cada usoLimpie Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónGarantía del sistema de control de emisiones GarantíasResponsabilidades de la garantía del propietario Información sobre emisiones Garantía Limitada Page Servicio común despide Especificaciones del productoTemperatura del suministro

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents