Briggs & Stratton 020364-0 manual How to Start Your Pressure Washer

Page 14

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step. This starting information also applies if you have let the pressure washer sit idle for at least

aday.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.8 gallons per minute and no less than 20 PSI at pressure washer end of garden hose. DO NOT siphon supply water.

2.Check that high pressure hose is tightly connected to spray gun and pump. See Assembly section.

3.Make sure unit is in a level position.

4.Uncoil high pressure hose from hose reel completely before using pressure washer.

5.Connect garden hose to water inlet on pressure washer pump.

6.Turn ON water, point gun in a safe direction and squeeze trigger to purge pump system of air and impurities.

NOTICE

DO NOT run the pump without the water supply connected and turned on.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

7.Attach nozzle extension to spray gun. Tighten by hand.

8.Choose Project Pro® nozzle you want to use, pull back on collar of nozzle extension, insert nozzle and release collar. Tug on nozzle to make sure it is securely in place. See How to Use Project Pro® Nozzles.

9.Engage trigger lock (A) on spray gun trigger.

A

10.Rotate fuel shut-off valve to “On” position (B) (fully counter-clockwise).

B

11.Move throttle control lever (C) to “High” position, shown on engine as a rabbit .

 

 

C

12.

Move choke lever to “Choke”

position.

NOTE: For a warm engine, be sure the choke lever is in the

“Run” position.

IMPORTANT: Before starting the pressure washer, be sure you are wearing adequate safety goggles.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

•Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate safety goggles.

•NEVER substitute safety glasses for safety goggles.

13.When starting engine, position yourself as recommended below and grasp starter grip handle and pull slowly until you feel some resistance. Then pull rapidly to start engine.

14

BRIGGSandSTRATTON.COM

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Engine Where to Find UsPressure Washer Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionWhen Adding or Draining Fuel Unintentional sparking can result in fire or electric shock Broken bones, fractures, bruises, or sprains could resultContact with muffler area can result in serious burns Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassUnpack Pressure Washer AssemblyAttach Handle and Accessory Tray Items in the carton includeAttach Hose Reel Fuel must meet these requirements Add Engine OilAdd Fuel High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpOil Drain Drain engine oil here Pump Develops high pressure Features and ControlsWater Inlet Connection for garden hose Clearances and Air Movement OperationPressure Washer Location How to Start Your Pressure Washer Attach nozzle extension to spray gun. Tighten by handLever to Choke position, then to Run position How to Stop Your Pressure WasherEngage trigger lock on spray gun when not in use Follow these instructions to change Project Pro nozzles How to Use Accessory TrayHow to Use Project Pro Nozzles To apply detergent, follow these steps Cleaning and Applying DetergentUsage Tips Automatic Cool Down System Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing For RinsingPressure Washer Maintenance MaintenanceMaintenance Schedule Check High Pressure Hoses Nozzle MaintenanceRing Maintenance Check Detergent Siphoning TubeChecking Oil Level Engine MaintenanceOil Oil Recommendations Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Spark Arrester ServiceAfter Each Use Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionWarranties Emissions Control System WarrantyOwner’s Warranty Responsibilities Claims and Coverage Exclusions MaintenanceEmission Information Limited Warranty Page 800 Product SpecificationsCommon Service Parts Manual del Operario Motor Dónde encontrarnosLimpiadora a Presión Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de Operario Características y mandos OperandoReglas de seguridad Seguridad de OperarioDerscripción del Equipo Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Conecte el asa y bandeja accesoria MontajeDesembale la limpiadora a presión Los artículos que se encuentran en la caja sonFije el carrete de manguera El combustible debe reunir los siguientes requisitos Agregar aceite al motorAgregue combustible Gran altitudProporcione el suministro de agua adecuado Conecte la manguera y el suministro de agua a la bombaLista de revision previa al arranque del motor Características y mandos Bomba Desarrolla alta presión de aguaUbicación del limpiadora a presión OperandoPresión Cómo darle arranque a su máquina limpiadora aAdvertencia Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laLa Presión Baja Utilización de la bandeja de accesoriosCómo usar las boquillas Project Pro La Presión AltaUso inclina Limpieza y aplicación del detergenteElija la boquilla Project Pro que desee Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Enjuage de la máquina limpiadora a presiónLimpieza del tubo de inyección de detergente Para EnjuageMantenimiento de la limpiadora a presión MantenimientoPlan de mantenimiento Chequee el tubo de sifón del detergente Revise y limpie el colador de entradaCompruebe las mangueras de alta presión Revise la pistolaMantenimiento del motor Suministre servicio al depurador de aire una vez cada Asegúrese de que la unidad esté en una superficie planaServicio del depurador de aire Servicio del bujíaLimpie Despues de cada usoSistema de refrigeración de aire Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónResponsabilidades de la garantía del propietario GarantíasGarantía del sistema de control de emisiones Información sobre emisiones Garantía Limitada Page Temperatura del suministro Especificaciones del productoServicio común despide

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents