Briggs & Stratton 020364-0 manual Cleaning and Applying Detergent, Usage Tips

Page 17

3. Select desired Project Pro® nozzle:

 

• For applying detergent, applies project specific

• For delicate rinse (lower pressure and higher flow),

 

cleaners to help break down stubborn dirt and

for gentle cleaning of cars/trucks, boats, RV’s, patio

 

grime on a variety of surfaces, select black Project

furniture, lawn equipment, etc., select yellow

 

Pro® cleaning detergent nozzle.

Delicate Project Pro® nozzle.

 

 

 

 

 

 

 

 

 

 

 

 

 

•For general rinsing (medium pressure and medium flow), ideal for most all purpose cleaning such as home siding, brick patios, wood decks, driveways and sidewalks, garage floors, etc., select orange General Project Pro® nozzle.

•For maximum rinsing (higher pressure and lower flow), for stubborn or hard to reach surface such as second story surfaces, paint removal, oil stains, rust removal or other stubborn substances (tar, gum, grease, wax, etc.), select red Max Project Pro® nozzle.

4.Pull back on collar, insert new Project Pro® nozzle and release collar. Tug on Project Pro® nozzle to make sure it is securely in place.

Usage Tips

•For most effective cleaning, keep nozzle from 8 to

24 inches (20 to 61 cm) away from cleaning surface.

•If you get nozzle too close, especially using a high pressure nozzle, you may damage surface being cleaned.

•DO NOT get closer than 6 inches (15 cm) when cleaning tires.

Cleaning and Applying Detergent

CAUTION

Chemicals can cause bodily injury, and/or property damage.

•NEVER use caustic liquid with pressure washer.

•Use ONLY pressure washer safe detergents/soaps. Follow all manufacturers instructions.

To apply detergent, follow these steps:

1.Review use of Project Pro® nozzles.

2.Prepare detergent solution as required by job.

3.Place small filter end of detergent siphoning tube into detergent container.

NOTICE

Contact with the hot muffler can damage detergent siphoning tube.

•When inserting the filter into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler.

NOTE: Make sure the filter is fully submerged in detergent while applying detergent.

4. Make sure black detergent nozzle is installed.

NOTE: Detergent cannot be applied with the high pressure Project Pro® nozzle (Orange, Yellow or Red).

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operator’s Manual Pressure Washer Where to Find UsEngine Date PurchasedTable of Contents Safety Rules Operator SafetyHazard Symbols and Meanings Equipment DescriptionWhen Adding or Draining Fuel Unintentional sparking can result in fire or electric shock Broken bones, fractures, bruises, or sprains could resultContact with muffler area can result in serious burns High pressure spray may damage fragile items including glass Risk of eye injury Spray can splash back or propel objectsAttach Handle and Accessory Tray AssemblyUnpack Pressure Washer Items in the carton includeAttach Hose Reel Add Fuel Add Engine OilFuel must meet these requirements High AltitudeConnect Hose and Water Supply to Pump Checklist Before Starting EngineOil Drain Drain engine oil here Pump Develops high pressure Features and ControlsWater Inlet Connection for garden hose Clearances and Air Movement OperationPressure Washer Location Attach nozzle extension to spray gun. Tighten by hand How to Start Your Pressure WasherLever to Choke position, then to Run position How to Stop Your Pressure WasherEngage trigger lock on spray gun when not in use Follow these instructions to change Project Pro nozzles How to Use Accessory TrayHow to Use Project Pro Nozzles To apply detergent, follow these steps Cleaning and Applying DetergentUsage Tips Pressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief For RinsingPressure Washer Maintenance MaintenanceMaintenance Schedule Ring Maintenance Nozzle MaintenanceCheck High Pressure Hoses Check Detergent Siphoning TubeOil Oil Recommendations Engine MaintenanceChecking Oil Level Adding Engine OilTo service the air cleaner, follow these steps Service Air CleanerService Spark Plug Spark Arrester ServiceAfter Each Use Long Term Storage Winter StorageProblem Cause Correction TroubleshootingWarranties Emissions Control System WarrantyOwner’s Warranty Responsibilities Claims and Coverage Exclusions MaintenanceEmission Information Limited Warranty Page 800 Product SpecificationsCommon Service Parts Manual del Operario Limpiadora a Presión Dónde encontrarnosMotor Fecha de compraSeguridad de Operario Resolución de problemas GarantíasMontaje Características y mandos OperandoReglas de seguridad Seguridad de OperarioDerscripción del Equipo Opere el limpiadora a presión Solamente al aire libre Riesgo de electrocuciónCuando Pruebe LA Bujía DEL Motor Aviso Desembale la limpiadora a presión MontajeConecte el asa y bandeja accesoria Los artículos que se encuentran en la caja sonFije el carrete de manguera Agregue combustible Agregar aceite al motorEl combustible debe reunir los siguientes requisitos Gran altitudProporcione el suministro de agua adecuado Conecte la manguera y el suministro de agua a la bombaLista de revision previa al arranque del motor Bomba Desarrolla alta presión de agua Características y mandosPresión OperandoUbicación del limpiadora a presión Cómo darle arranque a su máquina limpiadora aAdvertencia Cuando arranque el motor, mueva lentamente la Cómo detener su máquina limpiadora a presiónCómo usar las boquillas Project Pro Utilización de la bandeja de accesoriosLa Presión Baja La Presión AltaElija la boquilla Project Pro que desee Limpieza y aplicación del detergenteUso inclina Para aplicar el detergente, siga los siguientes pasosLimpieza del tubo de inyección de detergente Enjuage de la máquina limpiadora a presiónSistema de enfriamiento automático alivio térmico Para EnjuageMantenimiento de la limpiadora a presión MantenimientoPlan de mantenimiento Compruebe las mangueras de alta presión Revise y limpie el colador de entradaChequee el tubo de sifón del detergente Revise la pistolaMantenimiento del motor Servicio del depurador de aire Asegúrese de que la unidad esté en una superficie planaSuministre servicio al depurador de aire una vez cada Servicio del bujíaLimpie Despues de cada usoSistema de refrigeración de aire Almacenamiento prolongado Almacenamiento para inviernoProblema Causa Solución Resolución de problemasResponsabilidades de la garantía del propietario GarantíasGarantía del sistema de control de emisiones Información sobre emisiones Garantía Limitada Page Temperatura del suministro Especificaciones del productoServicio común despide

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents