Briggs & Stratton 020364-0 manual Pressure Washer Rinsing, Cleaning Detergent Siphoning Tube

Page 18

5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

NOTICE

You must attach all hoses before you start the engine.

•Starting the engine without all the hoses connected and without the water turned ON will damage the pump.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Engage trigger lock on spray gun and start engine following instructions How to Start Your Pressure Washer.

7.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

8.Allow detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1.Engage trigger lock on spray gun.

2.Remove black detergent nozzle from nozzle extension.

3.Select and install desired high pressure nozzle following instructions How to Use Project Pro® Nozzles.

4.Keep spray gun a safe distance from area you plan to spray.

WARNING

Kickback from spray gun can cause you to fall.

•Operate pressure washer from a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding, or any other similar location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

5.Apply a high pressure spray to a small area and then check surface for damage. If no damage is found, you can assume it is okay to continue rinsing.

6.Start at top of area to be rinsed, working down with same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

1.Place detergent siphoning tube/filter in a bucket full of clean water.

2.Engage trigger lock on spray gun.

3.Remove high pressure nozzle from nozzle extension.

4.Select and install black detergent nozzle following instructions How to Use Project Pro® Nozzles.

5.Flush for 1-2 minutes.

6.Shut off engine following instructions How to Stop Pressure Washer and turn off water supply.

7.ALWAYS point spray gun in a safe direction and squeeze spray gun trigger to release retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hoses connected to pump, hose reel and spray gun while system is pressurized.

•ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F. The system engages to cool the pump by discharging the warm water onto the ground.

18

BRIGGSandSTRATTON.COM

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator’s Manual Engine Where to Find UsPressure Washer Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionWhen Adding or Draining Fuel Broken bones, fractures, bruises, or sprains could result Contact with muffler area can result in serious burnsUnintentional sparking can result in fire or electric shock Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassUnpack Pressure Washer AssemblyAttach Handle and Accessory Tray Items in the carton includeAttach Hose Reel Fuel must meet these requirements Add Engine OilAdd Fuel High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpFeatures and Controls Water Inlet Connection for garden hoseOil Drain Drain engine oil here Pump Develops high pressure Operation Pressure Washer LocationClearances and Air Movement How to Start Your Pressure Washer Attach nozzle extension to spray gun. Tighten by handHow to Stop Your Pressure Washer Engage trigger lock on spray gun when not in useLever to Choke position, then to Run position How to Use Accessory Tray How to Use Project Pro NozzlesFollow these instructions to change Project Pro nozzles Cleaning and Applying Detergent Usage TipsTo apply detergent, follow these steps Automatic Cool Down System Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing For RinsingMaintenance Maintenance SchedulePressure Washer Maintenance Check High Pressure Hoses Nozzle MaintenanceRing Maintenance Check Detergent Siphoning TubeChecking Oil Level Engine MaintenanceOil Oil Recommendations Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Spark Arrester ServiceAfter Each Use Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionEmissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Page Product Specifications Common Service Parts800 Manual del Operario Motor Dónde encontrarnosLimpiadora a Presión Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de Operario Características y mandos OperandoSeguridad de Operario Derscripción del EquipoReglas de seguridad Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Conecte el asa y bandeja accesoria MontajeDesembale la limpiadora a presión Los artículos que se encuentran en la caja sonFije el carrete de manguera El combustible debe reunir los siguientes requisitos Agregar aceite al motorAgregue combustible Gran altitudConecte la manguera y el suministro de agua a la bomba Lista de revision previa al arranque del motorProporcione el suministro de agua adecuado Características y mandos Bomba Desarrolla alta presión de aguaUbicación del limpiadora a presión OperandoPresión Cómo darle arranque a su máquina limpiadora aAdvertencia Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laLa Presión Baja Utilización de la bandeja de accesoriosCómo usar las boquillas Project Pro La Presión AltaUso inclina Limpieza y aplicación del detergenteElija la boquilla Project Pro que desee Para aplicar el detergente, siga los siguientes pasosSistema de enfriamiento automático alivio térmico Enjuage de la máquina limpiadora a presiónLimpieza del tubo de inyección de detergente Para EnjuageMantenimiento Plan de mantenimientoMantenimiento de la limpiadora a presión Chequee el tubo de sifón del detergente Revise y limpie el colador de entradaCompruebe las mangueras de alta presión Revise la pistolaMantenimiento del motor Suministre servicio al depurador de aire una vez cada Asegúrese de que la unidad esté en una superficie planaServicio del depurador de aire Servicio del bujíaDespues de cada uso Sistema de refrigeración de aireLimpie Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónGarantías Garantía del sistema de control de emisionesResponsabilidades de la garantía del propietario Información sobre emisiones Garantía Limitada Page Especificaciones del producto Servicio común despideTemperatura del suministro

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents