Briggs & Stratton 020364-0 manual Winter Storage, Long Term Storage

Page 24

Winter Storage

NOTICE

You must protect your unit from freezing temperatures.

•Failure to do so will permanently damage your pump and render your unit inoperable.

•Freeze damage is not covered under warranty.

To protect the unit from freezing temperatures:

1.Follow steps 1-3 in the previous section After Each Use.

2.Use pump saver, Model 6039, to treat pump. This minimizes freeze damage and lubricates pistons and seals.

3.If pump saver is not available, connect a 3-foot section of garden hose to water inlet adapter. Pour RV-antifreeze (antifreeze without alcohol) into hose. Pull recoil handle twice. Disconnect 3-foot hose.

4.Store unit in a clean, dry area.

Long Term Storage

If you do not plan to use the pressure washer for more than 30 days, you must prepare the engine and pump for long term storage.

Protect Fuel System

Fuel Additive:

Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs

&Stratton FRESH START™ fuel stabilizer, available as a liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel stabilizer is added according to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel system. The engine and fuel can then be stored up to

24 months.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into an approved container. Run the engine until it stops from lack of fuel. The use of a fuel stabilizer in the storage container is recommended to maintain freshness.

Change Oil

While engine is still warm, drain oil from crankcase. Refill with recommended grade. See Changing Engine Oil in Engine Maintenance.

Oil Cylinder Bore

•Remove spark plug and pour about 1/2 ounce (15 ml) of clean engine oil into the cylinder.

•Install spark plug and pull starter handle slowly to distribute oil.

Protecting the Pump

To protect the pump from damage caused by mineral deposits or freezing, use PumpSaver, Model 6039, to treat pump. This prevents freeze damage and lubricates pistons and seals.

NOTICE

You must protect your unit from freezing temperatures.

•Failure to do so will permanently damage your pump and render your unit inoperable.

•Freeze damage is not covered under warranty.

NOTE: PumpSaver is available as an optional accessory. It is not included with the pressure washer. Contact the nearest authorized service center to purchase PumpSaver.

To use PumpSaver, make sure the pressure washer is turned off and disconnected from supply water. Read and follow all instructions and warnings given on the PumpSaver container.

Other Storage Tips

1.DO NOT store fuel from one season to another unless it has been treated as described in Protect Fuel System.

2.Replace fuel container if it starts to rust. Rust and/or dirt in fuel can cause problems if it’s used with this unit.

3.Cover unit with a suitable protective cover that does not retain moisture.

WARNING

Storage covers can be flammable.

•DO NOT place a storage cover over a hot pressure washer.

•Let equipment cool for a sufficient time before placing the cover on the equipment.

4.Store unit in a clean and dry area.

24

BRIGGSandSTRATTON.COM

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s Manual Where to Find Us Pressure WasherEngine Date PurchasedTable of Contents Operator Safety Safety RulesHazard Symbols and Meanings Equipment DescriptionWhen Adding or Draining Fuel Broken bones, fractures, bruises, or sprains could result Contact with muffler area can result in serious burnsUnintentional sparking can result in fire or electric shock Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassAssembly Attach Handle and Accessory TrayUnpack Pressure Washer Items in the carton includeAttach Hose Reel Add Engine Oil Add FuelFuel must meet these requirements High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpFeatures and Controls Water Inlet Connection for garden hoseOil Drain Drain engine oil here Pump Develops high pressure Operation Pressure Washer LocationClearances and Air Movement How to Start Your Pressure Washer Attach nozzle extension to spray gun. Tighten by handHow to Stop Your Pressure Washer Engage trigger lock on spray gun when not in useLever to Choke position, then to Run position How to Use Accessory Tray How to Use Project Pro NozzlesFollow these instructions to change Project Pro nozzles Cleaning and Applying Detergent Usage TipsTo apply detergent, follow these steps Cleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal Relief For RinsingMaintenance Maintenance SchedulePressure Washer Maintenance Nozzle Maintenance Ring MaintenanceCheck High Pressure Hoses Check Detergent Siphoning TubeEngine Maintenance Oil Oil RecommendationsChecking Oil Level Adding Engine OilService Air Cleaner To service the air cleaner, follow these stepsService Spark Plug Spark Arrester ServiceAfter Each Use Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionEmissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Page Product Specifications Common Service Parts800 Manual del Operario Dónde encontrarnos Limpiadora a PresiónMotor Fecha de compraResolución de problemas Garantías Seguridad de OperarioMontaje Características y mandos OperandoSeguridad de Operario Derscripción del EquipoReglas de seguridad Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Montaje Desembale la limpiadora a presiónConecte el asa y bandeja accesoria Los artículos que se encuentran en la caja sonFije el carrete de manguera Agregar aceite al motor Agregue combustibleEl combustible debe reunir los siguientes requisitos Gran altitudConecte la manguera y el suministro de agua a la bomba Lista de revision previa al arranque del motorProporcione el suministro de agua adecuado Características y mandos Bomba Desarrolla alta presión de aguaOperando PresiónUbicación del limpiadora a presión Cómo darle arranque a su máquina limpiadora aAdvertencia Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laUtilización de la bandeja de accesorios Cómo usar las boquillas Project ProLa Presión Baja La Presión AltaLimpieza y aplicación del detergente Elija la boquilla Project Pro que deseeUso inclina Para aplicar el detergente, siga los siguientes pasosEnjuage de la máquina limpiadora a presión Limpieza del tubo de inyección de detergenteSistema de enfriamiento automático alivio térmico Para EnjuageMantenimiento Plan de mantenimientoMantenimiento de la limpiadora a presión Revise y limpie el colador de entrada Compruebe las mangueras de alta presiónChequee el tubo de sifón del detergente Revise la pistolaMantenimiento del motor Asegúrese de que la unidad esté en una superficie plana Servicio del depurador de aireSuministre servicio al depurador de aire una vez cada Servicio del bujíaDespues de cada uso Sistema de refrigeración de aireLimpie Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónGarantías Garantía del sistema de control de emisionesResponsabilidades de la garantía del propietario Información sobre emisiones Garantía Limitada Page Especificaciones del producto Servicio común despideTemperatura del suministro

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents