Briggs & Stratton 020364-0 manual Check High Pressure Hoses, Check Detergent Siphoning Tube

Page 20

Check High Pressure Hoses

The high pressure hoses can develop leaks from wear, kinking, or abuse. Inspect the hoses each time before using them. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair high pressure hose. Replace it.

•Replacement hose rating MUST exceed maximum pressure rating of unit.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged. The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Spray Gun

Examine the hose connection to the spray gun and make sure it is secure. Test the trigger by pressing it and making sure it “springs back” into place when you release it. Put the trigger lock in the ON position and test the trigger. You should not be able to press the trigger.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean the nozzle following these instructions:

1.Shut off engine and turn off water supply.

2.ALWAYS point spray gun in a safe direction and squeeze spray gun trigger to release retained high water pressure.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hoses connected to pump, hose reel and spray gun while system is pressurized.

•ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

3.Remove nozzle from end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting nozzle (A).

A

5. Remove nozzle extension from spray gun.

7.Using a garden hose, remove additional debris by back flushing water through nozzle extension. Back flush between 30 to 60 seconds.

8.Reinstall nozzle into nozzle extension.

9.Reconnect nozzle extension to spray gun.

10.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

11.Engage trigger lock on spray gun and start engine following instructions How to Start Your Pressure Washer.

12.Test pressure washer by operating with each quick connect nozzle.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 6048, by contacting the nearest authorized service center. It is not included with the pressure washer. This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

20

BRIGGSandSTRATTON.COM

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operator’s Manual Where to Find Us Pressure WasherEngine Date PurchasedTable of Contents Operator Safety Safety RulesHazard Symbols and Meanings Equipment DescriptionWhen Adding or Draining Fuel Unintentional sparking can result in fire or electric shock Broken bones, fractures, bruises, or sprains could resultContact with muffler area can result in serious burns Risk of eye injury Spray can splash back or propel objects High pressure spray may damage fragile items including glassAssembly Attach Handle and Accessory TrayUnpack Pressure Washer Items in the carton includeAttach Hose Reel Add Engine Oil Add FuelFuel must meet these requirements High AltitudeChecklist Before Starting Engine Connect Hose and Water Supply to PumpOil Drain Drain engine oil here Pump Develops high pressure Features and ControlsWater Inlet Connection for garden hose Clearances and Air Movement OperationPressure Washer Location How to Start Your Pressure Washer Attach nozzle extension to spray gun. Tighten by handLever to Choke position, then to Run position How to Stop Your Pressure WasherEngage trigger lock on spray gun when not in use Follow these instructions to change Project Pro nozzles How to Use Accessory TrayHow to Use Project Pro Nozzles To apply detergent, follow these steps Cleaning and Applying DetergentUsage Tips Cleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal Relief For RinsingPressure Washer Maintenance MaintenanceMaintenance Schedule Nozzle Maintenance Ring MaintenanceCheck High Pressure Hoses Check Detergent Siphoning TubeEngine Maintenance Oil Oil RecommendationsChecking Oil Level Adding Engine OilService Air Cleaner To service the air cleaner, follow these stepsService Spark Plug Spark Arrester ServiceAfter Each Use Winter Storage Long Term StorageTroubleshooting Problem Cause CorrectionWarranties Emissions Control System WarrantyOwner’s Warranty Responsibilities Claims and Coverage Exclusions MaintenanceEmission Information Limited Warranty Page 800 Product SpecificationsCommon Service Parts Manual del Operario Dónde encontrarnos Limpiadora a PresiónMotor Fecha de compraResolución de problemas Garantías Seguridad de OperarioMontaje Características y mandos OperandoReglas de seguridad Seguridad de OperarioDerscripción del Equipo Riesgo de electrocución Opere el limpiadora a presión Solamente al aire libreCuando Pruebe LA Bujía DEL Motor Aviso Montaje Desembale la limpiadora a presiónConecte el asa y bandeja accesoria Los artículos que se encuentran en la caja sonFije el carrete de manguera Agregar aceite al motor Agregue combustibleEl combustible debe reunir los siguientes requisitos Gran altitudProporcione el suministro de agua adecuado Conecte la manguera y el suministro de agua a la bombaLista de revision previa al arranque del motor Características y mandos Bomba Desarrolla alta presión de aguaOperando PresiónUbicación del limpiadora a presión Cómo darle arranque a su máquina limpiadora aAdvertencia Cómo detener su máquina limpiadora a presión Cuando arranque el motor, mueva lentamente laUtilización de la bandeja de accesorios Cómo usar las boquillas Project ProLa Presión Baja La Presión AltaLimpieza y aplicación del detergente Elija la boquilla Project Pro que deseeUso inclina Para aplicar el detergente, siga los siguientes pasosEnjuage de la máquina limpiadora a presión Limpieza del tubo de inyección de detergenteSistema de enfriamiento automático alivio térmico Para EnjuageMantenimiento de la limpiadora a presión MantenimientoPlan de mantenimiento Revise y limpie el colador de entrada Compruebe las mangueras de alta presiónChequee el tubo de sifón del detergente Revise la pistolaMantenimiento del motor Asegúrese de que la unidad esté en una superficie plana Servicio del depurador de aireSuministre servicio al depurador de aire una vez cada Servicio del bujíaLimpie Despues de cada usoSistema de refrigeración de aire Almacenamiento para invierno Almacenamiento prolongadoResolución de problemas Problema Causa SoluciónResponsabilidades de la garantía del propietario GarantíasGarantía del sistema de control de emisiones Información sobre emisiones Garantía Limitada Page Temperatura del suministro Especificaciones del productoServicio común despide

020364-0 specifications

The Briggs & Stratton 020364-0 is a robust and efficient small engine designed for a variety of outdoor power equipment applications. This engine is particularly well-regarded in the lawn care and garden equipment industries, owing to its reliability, performance, and ease of maintenance.

One of the standout features of the Briggs & Stratton 020364-0 is its powerful 6.75 foot-pounds of torque output. This engine's overhead valve design enhances fuel efficiency and provides improved performance across different operating conditions. The engine utilizes a 190cc displacement which allows for a higher level of power delivery, making it suitable for demanding tasks such as mowing larger lawns or heavy-duty garden work.

In addition to its power, the 020364-0 comes with an easy-start recoil system, which reduces the effort required to start the engine. This feature is particularly beneficial for users who may prefer a hassle-free experience when starting their lawn mowers or other equipment. The engine’s design includes a float carburetor that optimizes fuel delivery and efficiency, ensuring that the engine runs smoothly even in varying temperature and altitude conditions.

The Briggs & Stratton 020364-0 is also built with user convenience in mind. It is equipped with a dual-element air filter that protects the engine from dirt and debris, extending the engine's lifespan and reducing the need for frequent maintenance. Furthermore, the engine features a durable cast iron cylinder sleeve, enhancing its resistance to wear and improving its performance longevity.

Another important characteristic is its lightweight design, which facilitates easier maneuverability when installed in different power equipment. Users appreciate the efficiency of this engine, as it often translates to lower operational costs over time.

Given its reliable performance, innovative technologies, and user-friendly features, the Briggs & Stratton 020364-0 is an excellent choice for anyone in need of a dependable engine for various outdoor applications. Whether you are a professional landscaper or a homeowner maintaining a garden, this engine guarantees robust power and durability in every task.
Top Page Image Contents