Zenoah HTZ2401-CA, CHTZ2401L manual Intake AIR Cooling Vent, Blades

Page 36

English

8. Maintenance

MA4

MA5

MA6

(1)

 

(2)

 

(3)

leakage is found, stop using the machine and have it repaired immediately.

•Note that failing to do so may result in the engine catching on fire.

■INTAKE AIR COOLING VENT

WARNING

•Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.

•Clean the cylinder fins with compressed air or a brush. (MA4)

IMPORTANT

•If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the hedge-trimmer.

■BLADES

Oil blades each gas tank filling (MA5).

WARNING

•Make sure that the blade bolts are well tightened.

•The blade assembly is designed to automatically compensate for any play between the blades.

Check the cutting edges and reform with a flat file. (MA6)

Point :

1.Keep the end corner sharp.

2.Round the root of the edge.

3.Do not use water when using a grinder.

IMPORTANT

•When mounting the blade, make sure to fasten the spacer, washer and bolt, then fasten the nut.

(1)

Bolt

(2)

Plate

(3)

Spacer

(4)

Nut

(4)

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationModel Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes ModeloSymbols on the machine Emplacement PosiciónFor safe operation Working ConditionWorking Circumstance Conditions DE Travail Condición DE TrabajoCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Arranque DE LA MáquinaUtilisation DE LA Machine Empleo DEL ProductoMaintenance ManualIf Someone Comes SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulation DU Carburant TransportManejo DEL Combustible Llenar una vez que el motor se haya enfriadoWhen using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Lors de l’utilisation de la véritable huile RedMax/ZENOAHProporción DE LA Mezcla Recomendada Gasolina 50 Aceite Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteOperation OP3 7 6Starting Engine Cutting head will start moving upon the engine startsFonctionnement Uso Adjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Fonctionnement DU MoteurReglage DU Ralenti Apagado DEL MotorHOW to USE Handle CHTZ2401/CHTZ2401-CA onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarHedge Trimming Techniques Vertical cutHorizontal cut Coupe horizontale Técnicas DE RecorteCorte vertical Corte horizontalMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugFiltre a AIR Filtre a CarburantBougie D’ALLUMAGE Filtro DE AireIntake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR LamesVentilación DE Refrigeración DEL Aire DE Admisión CuchillasSafety Lock MA7 Sharpening MA8Reduction Gearbox Affûtage MA8 Afilado MA8Verrou DE Sécurité MA7 Dispositivo DE Seguridad MA7 Reducteur MA9Procedures to be Performed After Every 100 Hours of USE StorageDisposal ANTI-VIBRATION SystemEntretien Mantenimiento RangementAlmacenamiento Troubleshooting guide 11. Guía de localización y solución de problemasGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsControl DE Emisiones CHTZ2401-CA/CHTZ2401L-CA

CHTZ2401L, CHTZ2401, HTZ2401, HTZ2401-CA, HTZ2401L specifications

The Zenoah CHTZ2401, CHTZ2401L, HTZ2401L, HTZ2401, and HTZ2401-CA are a series of high-performance two-stroke engines designed for a variety of applications, including outdoor power equipment, gardening tools, and professional-grade machinery. These engines are renowned for their reliability, power output, and advanced features.

One of the main features of the Zenoah CHTZ2401 series is its powerful engine capacity. With a displacement of 24 cc, these engines deliver impressive power while remaining lightweight, making them suitable for handheld equipment. The CHTZ2401 and its variations provide a balance between performance and fuel efficiency, allowing users to work longer without frequently refueling.

A standout characteristic is the incorporation of Zenoah's advanced engine technologies. The engines are designed with a high compression ratio, which enhances combustion efficiency. This results in improved torque and power delivery, ensuring that the equipment can handle demanding tasks with ease. Additionally, the engines feature a unique exhaust system that minimizes emissions while maximizing power output, aligning with modern environmental standards.

The CHTZ2401 series also includes enhanced cooling systems, ensuring that the engines maintain optimal operating temperatures even during prolonged use. This feature is crucial in preventing overheating and extending the lifespan of the equipment. The lightweight design of these engines, often constructed with durable yet lightweight materials, contributes to the overall functionality and ease of use, especially for handheld applications.

Another important aspect is maintenance. The Zenoah engines are designed for easy access to components that require regular servicing, such as air filters and spark plugs. This user-friendly design lowers downtime and makes maintenance more convenient for users, whether they are professionals or casual gardeners.

In summary, the Zenoah CHTZ2401, CHTZ2401L, HTZ2401L, HTZ2401, and HTZ2401-CA engines represent cutting-edge technology in the realm of two-stroke engines. With their powerful performance, improved efficiency, and easy maintenance features, they are suitable for a wide range of applications, from landscaping to construction. As a result, they have become a popular choice among professionals who demand reliability and performance from their outdoor power equipment.
Top Page Image Contents