Zenoah BC535DLM, BC535DWM manual Operation Fonctionnement, OP5 OP6

Page 36

 

English

 

Français

 

 

8. Operation

8. Fonctionnement

 

 

 

 

 

OP5

OP6

STOPPING ENGINE (OP3)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the “O (STOP)” position. (OP3)

IMPORTANT

Except for an emergency, avoid stopping the engine while pulling the throttle lever.

ADJUSTING THROTTLE CABLE

The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP5)

(1) Cable adjuster

ADJUSTING IDLING SPEED (OP6)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise.

(1) Idle adjusting screw

NOTE

Warm up the engine before adjusting the idling speed.

de l’excès de carburant. Si le moteur refuse de démarrer après plusieurs tentatives infructueuses, placer le starter en position ouverte et tirer à nouveau plusieurs fois la corde de démarrage ou enlever et sécher la bougie.

ARRET DU MOTEUR (OP3)

1.Relâcher la manette d’accélérateur et laisser tourner le moteur pendant encore 30 secondes.

2.Placer le bouton de contact sur “(Arrêt) O”. (OP3)

IMPORTANT

Sauf en cas d’urgence, ne jamais couper le contact lorsqu’on accélére.

REGLAGE

CÂBLE

D’ACCÉLÉRATEUR

 

le jeu normal est de 1 à 2 mm mesuré au niveau du carburateur. Si nécessaire, effectuer ce réglage à l’aide du régleur. (OP5)

(1) Ajusteur de câble

REGLAGE DU RALENTI (OP6)

1.Lorsque le moteur a tendance à s’arrêter souvent au ralenti, tourner la vis dans le sens horaire.

2.Si la tête de coupe continue de tourner au ralenti après avoir relâché la manette d’accélérateur, tourner la vis dans le sens contraire des aiguilles d’une montre.

(1) Vis de réglage du ralenti

REMARQUE

Laisser chauffer le moteur avant d’effectuer le réglage du ralenti.

36

Image 36
Contents BC535DLM English Français Deutsch Italiano Español Page Risk of Damaging Hearing Hörschaden RisikoRischio DI Danno Uditivo Riesgo DE Daño AuditivoContents Tables des matieres Inhalt Indice Contenido Parts location Emplacement des pieces Cuchilla Specifications Fiche techniqueTechnische Daten Dati tecniciEspecificaciohes Symbols on the machine Symboles utilises sur la Machine EmplacementEtiquettes d’avertissement Machine Sur la machinePosizione Posición Position PosizioneEstrangulador For safe operation Consignes de securite Working ConditionWorking Circumstance Conditions DE TravailArbeitsbedingung ArbeitsumstandCondizioni Lavorative Circostanze LavorativeWorking Plan Before Starting the EnginePlan DE Travail LA MachineArbeitsplan Beim Planen der ArbeitseinsätzePiano DI Lavoro Plan DE TrabajoStarting the Engine Demarrage DU MoteurAvvertimento Advertencia DEN Motor StartenAccensione DEL Motore Arranque DEL MotorUsing the Product MaintenanceIf Someone Comes Utilisation DE LA MachineBenutzung DES Produktes Falls Sich Jemand NähertWartung Utilizzo DEL ProdottoCheck ok Handling FuelRefill after cooling the engine Komatsu ZenoahHandhabung DES Kraftstoffs Maneggio DEL CarburanteManipulación DEL Combustible Transportation TransportMotore si è raffreddato TrasportoTransporte Set up Assemblage SE1 SE2 SE3 SE4SE5 Zusammenbau Impostazione Montaje SE6 Balance Unit Equilibrage DE LA MachineZusammenbau Impostazione Montaje HOW to MIX Fuel Fuel CarburantComment Effectuer LE Melange DE Carburant ? Kraftstoff Carburante Combustible Mischen VON KraftstoffPER IL Miscelazione DEL Carburante Cómo Mezclar EL CombustibleFuel Carburant Fueling the Unit Remplissage DU ReservoirFor Your Engine LIFE, Avoid Pour Prolonger LA Duree DE VIE DU MOTEUR, NE PAS UtiliserEinfüllen VON Kraftstoff DAS Gerät Riempimento DEL Serbatoio DEL CarburanteCómo Cargar Combustible EN LA Unidad Wegen DER Lebensdauer Ihres GERÄTES, Folgendes VermeidenOperation Fonctionnement OP1 OP2 OP3OP4 Starting Engine Mise EN Marche DU MoteurBetrieb Funzionamento Uso Hinweis NotaStarten DES Motors Avviamento DEL Motore Arranque DEL Motor Operation Fonctionnement OP5 OP6Betrieb Funzionamento Uso OP7 OP8 OP9Verwendung Eines Metallblattes Scheda DI Applicazione Dello Strumento DA TaglioUtilizzo Della Lama DI Metallo Hoja DE Aplicación DEL CortadorControlling Blade Bounce How you can reduce the chance of kick outAvoid feeding the blade too rapidly Controle DES Coups DE ReculSchneidblattaufprall Steuern Controllo DEL Rimbalzo Della LamaControl DEL Contragolpe DE LA Hoja Line Head Usage Trimming Grass and WeedsUtilisation DE LA Tete DE Coupe a FIL Coupe DE Gazon OU D’HERBESVerwendung DES Schnurkopfes Gras UND Unkraut SchneidenUtilizzo Dello Strumento DA Taglio a Corda PER Tagliare L’ERBA E ErbacciaAdjusting the Line Length Reglage DE LA Longeur DU FIL DE CoupeEinstellung DER Schnurlänge Gradi verso la direzione dell’operazione. OP11Regolazione Della Lunghezza Della Corda Ajuste DE LA Longitud DE LA LíneaMaintenance Chart MaintenaceEntretien Tableau D’ENTRETIENWartung ManutenzioneMantenimiento Maintenace Entretien MA1MA2 MA3 MA4 Wartung Manutenzione Mantenimiento Wichtig ImportanteTightening Torque MufflerCouple DE Serrage SilencieuxAnzugsmoment DämpferTorsione DI Serraggio MarmittaProcedures to be Performed After Every 100 Hours of USE Procedure a Effectuer Toutes LES 100 Heures D’UTILISATIONMA6 MA7 Cylinder Intake air cooling vent backProcedure DA Effettuare Ogni 100 ORE DI Utilizzo Zylinder Ansaugluft-Kühlschlitze hintenAlle 100 Betriebsstunden Auszuführende Wartungsarbeiten Cilindro Toma de aire de refrigeración posteriorStorage Rangement Lagerung Immagazzinaggio Almacenamiento Troubleshooting guide Guide de localisation des pannesCheck Probable Causes Action Verification Causes Probables Action11. Guía de localización y solución de problemas FehlersucheLocalizzazione dei guasti Limited warranty Garantie limitée Garantiebestimmungen Garanzia limitata Garantía limitada

BC535DWM, BC535DLM specifications

The Zenoah BC535DLM and BC535DWM are cutting-edge brushcutters designed for both professional landscapers and gardening enthusiasts. They embody a perfect blend of power, efficiency, and user-friendly features that make them stand out in the competitive market of outdoor tools.

At the heart of these brushcutters is a robust 53cc, two-stroke engine that delivers impressive performance while maintaining low emissions. This power source allows users to tackle a variety of cutting tasks, from thick brush to dense undergrowth, with ease. The BC535DLM is particularly noted for its lightweight design, making it an ideal choice for lengthy jobs without causing significant fatigue.

One of the standout features of the Zenoah BC535DLM and BC535DWM is their advanced Anti-Vibration System. This technology significantly reduces vibration during operation, enhancing user comfort and control. The ergonomic handle design further complements this feature, allowing for prolonged usage without discomfort. Both models also include a multi-function control handle, which provides easy access to throttle and stop controls, improving the overall user experience.

The BC535DWM model, designed for a more demanding professional use, comes equipped with a high-efficiency cutting head. This feature is optimized for heavier-duty applications, ensuring that operators can effortlessly transition from lighter grasses to tougher weeds. Additionally, the BC535DWM supports a wider variety of accessories, helping professionals adapt their tools to multiple tasks easily.

Fuel efficiency is another hallmark of the Zenoah brand, as both models are designed to maximize runtime without compromising power. The fuel tank capacity allows for extended operation, minimizing downtime during larger landscaping projects. Furthermore, Zenoah's commitment to eco-friendly technologies means that both units are engineered to comply with stringent emission standards, making them a responsible choice for environmentally conscious users.

Durability and reliability are critical considerations in the design of the Zenoah BC535DLM and BC535DWM. These brushcutters are built with high-quality materials to withstand tough working conditions, ensuring long-lasting performance. Maintenance is straightforward, allowing users to keep their equipment in peak condition with minimal effort.

In summary, the Zenoah BC535DLM and BC535DWM brushcutters combine powerful engines, innovative technologies, and user-centric designs, making them ideal for a range of landscaping tasks. Whether you are a professional searching for dependable equipment or a hobbyist looking to enhance your gardening experience, these models offer a compelling solution with superior performance and comfort.