Troy-Bilt E683F, E683G Transmission Gear Oil Maintenance, Checking for Oil Leaks, Preparation

Section 5: Maintenance

WARNING Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come

to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key, if so equipped.

Failure to follow these instructions can result in serious personal injury or property damage.

IMPORTANT: Do not allow oil or grease to contact the pulleys, drive belt or reverse disc. This can cause the belt or disc to slip on the pulleys.

Lubricate the numbered areas in Figures

5-4 and 5-5, as follows:

1.Oil the wheel shaft between the wheel hubs and the transmission housing (A, Figure 5-4).

2.Oil all pivoting and connecting points on the Wheels/Tines/PTO Drive Lever and the Wheel Speed Lever (B, Figure 5-4).

3.Grease the face of the belt adjustment block (C, Figure 5-4).

4.Oil the Depth Regulator Lever, including the spring in the mounting bracket (D, Figure 5-4).

7.Grease left- and right-side engine mounting bars at the top, the middle, and bottom (G, Figure 5-4).

8.Grease the zerk grease fitting located on the pivot point at the end of the Wheel Speed Lever (H, Figure 5-4). If Wheel Speed Lever has a grease fitting on pivot assembly, apply 2-to-3 strokes of multi- purpose grease at beginning and end of tilling season.

9.Keep the PTO access area well-greased (I, Figure 5-5). If the Tines/PTO Clutch Lever becomes hard to move, squirt some oil into its access hole, and work it back and forth to disperse the oil.

Transmission Gear

Oil Maintenance

the transmissions. To allow for this oil expansion, both the power unit transmis- sion and the tine attachment transmis- sions have oil relief vents (Figure 5-6).

The vents allow small amounts of oil to seep out.

➨

➨

Figure 5-6: Oil relief vent locations.

If a serious leak is discovered, please

5.	Oil the full length of the throttle cable	Checking for Oil Leaks
		At 25-hour operation intervals, check the
casing (E, Figure 5-4).
6.	Oil threads on Handlebar Height Adjust-	tiller for oil leaks. Inspect for oil accumu-
		lations on the tiller or the floor where it’s
ment Lever (F, Figure 5-4).
		stored.
		A small amount of oil seepage or wetness

						around a shaft opening
						or cover is no cause for
					F
	B					alarm. But a heavy con-
				E		centration of oil is more
D	C
						serious. You should
						tighten all bolts immedi-
						ately, and replace any worn
	H				G	seals or gaskets.
						It may be impossible to
			B		A
						determine how much oil
Figure 5-4: Tiller lubrication points
						has been lost, so check
(wheel removed for clarity).						the oil levels in the PTO
						transmission and the
						tine attachment before
						using the tiller again. Add
						any necessary gear oil.
						Serious damage to the
						transmission components
						can result from operation
		I
						when gear oil levels are
						low.
						If tilling during very hot
Figure 5-5: Use grease liberally in PTO access area.						weather, the gear oil may
						heat up and expand inside

contact your authorized dealer or the Factory Technical Service Department for service advice.

Checking Gear Oil Levels

Every 30 hours of operation, check the gear oil level in both the power unit trans- mission and the tine attachment trans- mission. Operating them while low on gear oil (even briefly) can cause serious damage to internal components.

Preparation

1.The transmissions must be cool, since hot gear oil expands and gives a false reading.

2.The power unit transmission and the tine attachment transmission must be connected when checking (or adding) gear oil.

Checking the Power Unit Oil Level

1.Move the tiller to level ground. Move the Depth Regulator up so the tines rest on the ground.

2.Use a 3/8" wrench to remove the oil level check plug on the left side of the

transmission housing (Figure 5-7).

30