Polaris 280 Troubleshooting and Adjustments for Your Pool Cleaner
Page 9

Troubleshooting

If the Polaris cleaner displays the following actions, adjustments may be necessary to restore performance. Refer to exploded parts diagram for part references.

Action: Hangs up on steps or other obstacles for longer than 3 minutes.

Solution: 1. Check the wheel RPM.

2.Verify the back-up valve is cycling.

3.Adjust the thrust jet.

4.Remove unnecessary pool hardware or install a Ladder Guard Kit (order part #G21 from a Polaris dealer).

Action: Polaris is sluggish, running with less power than normal.

Solution: 1. Check the filter screen in the in-line filter and clean, if necessary.

2.Clean the skimmer basket, pump basket, and pool filter.

3.Check all of the hoses, connections, and swivels for leaks that could cause loss of water pressure.

4.Check the wheel RPM.

Action: Polaris flies around the pool and/or does not make contact with the bottom.

Solution: 1. Confirm that the blue restrictor disk is installed in the UWF to decrease water flow. Or, install the red restrictor disk to decrease water flow even more.

2.Check the wheel RPM. If more than 32 RPM, unscrew the pressure relief valve to decrease water flow to

the cleaner. Note: The pressure relief valve should only be adjusted when a restrictor is installed.

3.Verify the back-up valve is cycling. Hold the valve out of the water and watch the jet. It should come on and go off.

Action: Polaris does not back up.

Solution: 1. Verify the back-up valve

is cycling.

2.Check the wheel RPM.

3.If the bag is full, empty it.

4.If head float has water in it, replace it.

5.Make sure feed hose is floating.

Action: Polaris only turns in one direction.

Solution: 1. Adjust the thrust jet.

2.Make sure feed hose is floating.

Action: Feed hose becomes tangled.

Solution: 1. Remeasure the hose to verify that it is adjusted to the proper length for the

pool shape.

2.With the Polaris operating, check that the swivels in the hose and the hose connections turn freely.

3.Make sure feed hose is floating.

4.With the Polaris turned off, spin each of the wheels. All wheels should turn together.

Action: Sweep hose is sucked into

the vacuum tube.

Solution: 1. Make sure the opening at the end of the sweep hose is not blocked by the sweep hose scrubber.

2.Adjust the sweep hose to a gentle sweeping motion.

English

www.polarispool.com

Page 8 Page 10
Image 9
Page 8 Page 10
Contents N U a L For customer service or support Always remove the Polaris before swimmers enter the poolUS and Canada Introduction Polaris 280 Complete CleanerQuick Installation Instructions Install the Universal Wall FittingAdjust Feed Hose To Fit Pool Length Check for Proper RPM Assemble the CleanerIf count is less than 28 RPM If count is more than 32 RPMRoutine Maintenance Fine Tuning The Polaris CleanerEnglish Description Action Polaris does not back up TroubleshootingAction Polaris only turns in one direction Action Feed hose becomes tangledTroubleshooting Worksheet Page Informations importantes Service clientèle ou assistance techniquePolaris 280 complets Installation du raccord mural universel UWF Instructions d’installation rapideContrôle de la vitesse de rotation de la roue Assemblage du nettoyeurSi elle est inférieure à 28 t/min Si la vitesse est supérieure à 32 tr/minEntretien normal Réglage fin du nettoyeur PolarisVue éclatée Français Dépannage Action Le Polaris ne recule pasAction Le Polaris ne tourne que dans un seul sens Action Le tuyau darrivée forme des nœuds Action Le nettoyeur ne nettoie pas toute la piscineAction Le nettoyeur tourne en rond Couché sur le côté Page Kundendienst Wichtige InformationenPolaris 280 kompletter Reiniger EinleitungQuick Installationsanleitung Installation der universalen WandhalterungZufuhrschlauch passend zur Länge des Pools einstellen Umdrehungszahl der Räder überprüfen Montage des ReinigersBei weniger als 28 Umdrehungen pro Minute Bei mehr als 32 Umdrehungen pro MinuteRoutine Wartung Feineinstellung des Polaris ReinigersExplosionsdarstellung Deutsch Vorgang Polaris Rücklauf funktioniert nicht FehlerbehebungVorgang Der Zufuhrschlauch verwickelt sich Vorgang Der Polaris dreht sich nur in eine RichtungVorgang Der Sweep-Schlauch wird in das Saugrohr gesaugt Vorgang Der Reiniger reinigt nicht den gesamten PoolPage Atención a clientes o apoyo técnico Información importanteLimpiafondos completo Polaris IntroducciónInstrucciones para la instalación rápida Instale el conector universal de paredAjuste la manguera alimentadora al tamaño de la piscina Compruebe las RPM de la rueda Arme el limpiafondosSi gira a menos de 28 RPM Si gira a más de 32 RPMMantenimiento periódico Ajustes menores del limpiafondos PolarisDiagrama expandido de piezas No. No. pieza Descripción Cant Resolución de problemas Acción El Polaris no retrocedeAcción El Polaris gira siempre en el mismo sentido Acción La manguera alimentadora se atasca Acción El limpiafondos no limpia toda la piscinaAcción El limpiafondos está de lado, girando en círculos Page Per assistenza clienti o supporto Informazioni importantiIl dispositivo di pulizia completo Polaris IntroduzioneInstallazione del raccordo a parete universale Istruzioni per una rapida installazioneRegolazione della lunghezza del tubo di alimentazione Modo che si adatti a quella della piscinaMontaggio del dispositivo di pulizia Controllo dell’RPM delle ruoteManutenzione regolare Ottimizzazione della messa a punto del PolarisSchema esploso dei pezzi Italiano Individuazione e soluzione dei problemi Azione il Polaris non va in retromarciaAzione il Polaris si gira solo in una direzione Azione il tubo di alimentazione si ingarbuglia Page Informações importantes Aspirador completo Polaris IntroduçaoInstale a conexão universal de parede Instruções para instalação rápidaAjuste a mangueira de alimentação de acordo com o Comprimento da piscinaVerifique se a rotação da roda rpm está correcta Monte o aspiradorManutenção de rotina Regular o aspirador PolarisDiagrama das peças Peça no Descrição Identificação e correcção de problemas Acção O Polaris não recuaAcção O Polaris só se desvia numa direcção Acção O aspirador gira em círculos sobre a sua parte lateral Page EC Declaration of Conformity

280 specifications

The Polaris 280 is a highly regarded robotic pool cleaner engineered for efficiency and performance. Its innovative design makes it a popular choice among pool owners seeking a reliable cleaning solution. The Polaris 280 operates with a unique yet effective pressure-side cleaning system that utilizes the force of water to capture dirt, debris, and leaves from all surfaces of your pool, including the floor and walls.

One of the standout features of the Polaris 280 is its dual drive jet system, which powers its agile movement throughout the pool. This feature allows the unit to cover a large area quickly and efficiently, ensuring that the entire pool is clean in no time. The robust construction of the Polaris 280 is another highlight; it boasts a durable body designed to withstand harsh pool conditions, including exposure to chemicals and varying water temperatures.

The Polaris 280 is equipped with a powerful, high-efficiency filter bag that captures fine debris and dirt particles. The filter bag is easy to access and clean, promoting convenient maintenance and optimal performance. The model also features a 31-foot hose, which provides ample reach for most pool sizes, minimizing the need for additional extensions or adjustments.

Another significant characteristic of the Polaris 280 is its use of advanced technology to enhance its cleaning capabilities. The cleaner employs a patented back-up valve that allows it to reverse direction when encountering obstacles. This functionality minimizes stuck situations, ensuring uninterrupted cleaning and efficient navigation throughout the pool.

The Polaris 280 operates independently of the pool’s filtration system, allowing for significant water circulation and improving overall water quality. As a result, users can enjoy a cleaner swimming environment with less manual effort in maintaining pool hygiene.

Additionally, its easy installation process means that pool owners can set it up without requiring professional assistance. The Polaris 280 has also gained recognition for its reliability and effectiveness, with many satisfied users praising its performance and longevity.

In conclusion, the Polaris 280 is a powerful robotic pool cleaner combining advanced features, durable construction, and user-friendly operation. Its ability to efficiently clear debris while improving overall pool circulation makes it a top choice for pool maintenance enthusiasts. Whether you have an inground or above-ground pool, the Polaris 280 delivers a comprehensive cleaning experience tailored to meet your needs.
Top Page Image Contents