Troy-Bilt Two-Stage Snow Thrower Setting Up Your Snow Thrower, Prior to operating, Test on page

Page 7
Prior to operating

4. Finish securing chute control assembly to chute

 

3

 

 

support bracket with wing nut and hex screw removed

4

 

earlier. See Figure 4.

 

Setting Up

Your Snow

Thrower

5.Check that all cables are properly routed through the cable guide on top of the engine. See Figure 5.

The extension cord is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove it before operating the snow thrower.

CAUTION: Prior to operating your snow thrower, refer to Auger Control Test on page 13. Read and follow all instructions carefully, and perform all adjustments to verify your snow thrower is operating safely and properly.

Figure 4

CAUTION

 

 

Prior to operating

 

your snow thrower,

5

refer to Auger Control

Test on page 13.

 

Read and follow all

 

instructions care-

 

fully and perform all

 

adjustments to verify

 

your unit is operating

 

safely and properly.

Figure 5

Shear Pin Storage (optional)

An area for convenient shear pin storage is located under the plastic dash panel. See Figure 6.

Figure 6

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1 READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATIONOPERATOR’S MANUAL Two-Stage Snow ThrowerSafety Labels Table of ContentsFinding and Recording Model Number Customer SupportHEED ITS WARNING Your Responsibility Restrict the use Safety Labelsresult in personal injury. When you see this symbol in this manual and on the machinePractices Safe OperationTrainingPreparation Do not modify engine Maintenance & StorageSafe Operation Practices OperationSetting Up Your Snow Thrower instructions care adjustments to verifyPrior to operating Test on pageDrift Cutters If Equipped Tire Pressure Pneumatic Tires Clean-Out ToolClean-Out Tool Skid ShoesChoke Control Operating Your Snow ThrowerKnow Your Snow Thrower Shift LeverWheel Steering Controls Auger ControlDrive Control/ Auger Control Lock Four-Way Chute ControlStarting The Engine Gas & Oil Fill-UpStopping The Engine Electric Starter If EquippedAuger Control Test To Engage DriveTo Engage Augers Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlFigure 16A - Standard Skid Shoe Figure 16B - Reversible Skid Shoe Engine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesAuger Belt Replacement Always stop engine, disconnect spark Drive Belt Replacementof maintenance or adjustments on your machine AugersFriction Wheel Removal Off-Season Storage Remedy Trouble ShootingProblem CauseTWO YEAR SUPREME WARRANTY Description AUGER HOUSING COMPONENTS/COMPOSANTS DU LOGEMENT DES TARIÈRESWheel Assembly ModelPage PIÈCE PARTN DE DESCRIPTIONPage PIÈCE PARTN DE DESCRIPTIONPage DESCRIPTION 31A-6004 ANS DEUX DE SUPRÈME GARANTIE Problème SolutionDépannage CausesAVERTISSEMENT saison hors Remisageà carburant le Videz gaz 31 Figure d’entretien Régimefrottement de roue la de Démontage 32 Figure26 Figure transmission de courroie la de RemplacementTarières 28 Figure19 Figure la de courroie la de Remplacementtarière 23 Figureordinaire Patin - 18A Figure patins et plate Lame17 Figure réversible Patin - 16B Figure ordinaire Patin - 16A Figure 15 Figure Réglagestarière la de Commande Patinsvitesses de changement de Câble et transmission la de Commandegoulotte la de Commande vitesses de leviertarières les embrayer Pour souffleuse la de UtilisationAVERTISSEMENT tarière la de commande la de Testélectrique démarreur le d’utiliser d’huile et d’essence Pleinsmoteur du Arrêt modèles certains sur électrique Démarreurcontact de Clé échéant cas le tarières mission/des -trans de commande la de Blocageroues des d’orientation Commande échéant cas le poignéesà d’essence plein souffleuse la de Commandesdépart de Volet 11 Figurepneus des Pression montage de Instructionsgénéral d’ordre Recommandations goulotte la de dégagement de Outiléchéant cas le coupe de Barres montage de Instructions9 Figure 8 Figure 7 Figure de goupille la de Remisage cisaillement2 Figure 3 Figure1 Figure responsabilité Votre sécurité de ConsignesRemisage et Entretien SYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZPréparation sécuritéde Consignes Utilisationvous de avant arrêtées soient se sécurité de Étiquettesgoulotte la nettoyer pour dégagement de l’outil de servird’utilisation vente-après Servicemodèle de numéro le trouver Pour matières des Tableca.troybilt.www phases deux neige à SouffleuseD’UTILISATION NOTICE 4J1 N2G ONTARIO KITCHENER, 1386, Box .O .P
Top Page Image Contents