Troy-Bilt Two-Stage Snow Thrower warranty Setting Up Your Snow Thrower, Clean-Out Tool, Skid Shoes

Page 9

Clean-Out

Clean-Out

Tool

Figure 10

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger housing and is designed to clear a clogged chute. Refer to page 11 for instructions on how to properly use it.

NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces.

3

Setting Up

Your Snow

Thrower

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

NOTE: If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the snow thrower as instructed here.

3.Some adjustments will have to be made periodically to maintain your unit properly.

4.Periodically check all fasteners and make sure these are tight.

WARNING

Never use your hands to clean snow and ice from the chute assembly or auger housing.

IMPORTANT

Under any circum- stance do not exceed manufacturer’s recom- mended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

9

Image 9

Contents OPERATOR’S MANUAL READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATIONTwo-Stage Snow Thrower P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1Finding and Recording Model Number Table of ContentsCustomer Support Safety Labelsresult in personal injury. When you see this symbol Safety Labelsin this manual and on the machine HEED ITS WARNING Your Responsibility Restrict the useSafe Operation PracticesTrainingPreparation Safe Operation Practices Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Prior to operating adjustments to verifyTest on page instructions careDrift Cutters If Equipped Clean-Out Tool Clean-Out ToolSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow ThrowerShift Lever Choke ControlDrive Control/ Auger Control Lock Auger ControlFour-Way Chute Control Wheel Steering ControlsStopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped Starting The EngineTo Engage Augers To Engage DriveRecoil Starter Auger Control TestShift Cable Making AdjustmentsChute Control Drive Control & Shift LeverFigure 16A - Standard Skid Shoe Figure 16B - Reversible Skid Shoe Lubrication Maintaining Your Snow ThrowerShave Plate and Skid Shoes EngineAuger Belt Replacement of maintenance or adjustments on your machine Drive Belt ReplacementAugers Always stop engine, disconnect sparkFriction Wheel Removal Off-Season Storage Problem Trouble ShootingCause RemedyTWO YEAR SUPREME WARRANTY Wheel Assembly AUGER HOUSING COMPONENTS/COMPOSANTS DU LOGEMENT DES TARIÈRESModel DescriptionPage N DE PARTDESCRIPTION PIÈCEPage N DE PARTDESCRIPTION PIÈCEPage N DE 31A-6004 ANS DEUX DE SUPRÈME GARANTIE Dépannage SolutionCauses Problèmesaison hors Remisage AVERTISSEMENTà carburant le Videz gaz frottement de roue la de Démontage d’entretien Régime32 Figure 31 FigureTarières transmission de courroie la de Remplacement28 Figure 26 Figuretarière la de courroie la de Remplacement23 Figure 19 Figurepatins et plate Lame ordinaire Patin - 18A Figure17 Figure tarière la de Commande RéglagesPatins réversible Patin - 16B Figure ordinaire Patin - 16A Figure 15 Figuregoulotte la de Commande et transmission la de Commandevitesses de levier vitesses de changement de CâbleAVERTISSEMENT soufﬂeuse la de Utilisationtarière la de commande la de Test tarières les embrayer Pourmoteur du Arrêt d’huile et d’essence Pleinsmodèles certains sur électrique Démarreur électrique démarreur le d’utiliserroues des d’orientation Commande échéant cas le tarières mission/des -trans de commande la de Blocageéchéant cas le poignées contact de Clédépart de Volet soufﬂeuse la de Commandes11 Figure à d’essence pleingénéral d’ordre Recommandations montage de Instructionsgoulotte la de dégagement de Outil pneus des Pressionmontage de Instructions échéant cas le coupe de Barres9 Figure 8 Figure 7 Figure de goupille la de Remisage cisaillement3 Figure 2 Figure1 Figure Remisage et Entretien sécurité de ConsignesSYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZ responsabilité Votrede Consignes sécuritéUtilisation Préparationgoulotte la nettoyer pour sécurité de Étiquettesdégagement de l’outil de servir vous de avant arrêtées soient semodèle de numéro le trouver Pour vente-après Servicematières des Table d’utilisationD’UTILISATION NOTICE phases deux neige à Soufﬂeuse4J1 N2G ONTARIO KITCHENER, 1386, Box .O .P ca.troybilt.www