Troy-Bilt Two-Stage Snow Thrower warranty Maintaining Your Snow Thrower, Friction Wheel Removal

Page 19
Friction Wheel Removal

1

Figure 29

2

Figure 30

Manual backgroundManual background3Manual backgroundManual backgroundManual backgroundManual backgroundManual background

Figure 31

Friction Wheel Removal

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment on page 12 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary.

Place the shift lever in third Forward (F3) position.

Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

1.a. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it.

b.Remove the right-hand wheel by removing the screw and cupped washer which secure it to the axle.

2.Carefully remove the hex nut and washer which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame.

3.Carefully position the hex shaft downward and to the left before carefully sliding the friction wheel assembly off the shaft.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassembling the friction wheel and replacing only the rubber ring, proceed as follows:

4.Remove the four screws which secure the friction wheel’s side plates together.

Remove the rubber ring from between the plates.

Reassemble the side plates with a new rubber ring.

Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble components.

4

Figure 32

6

Maintaining

Your Snow

Thrower

When reassembling the friction wheel as- sembly, tighten each screw only one rota- tion before turning the wheel clockwise and proceeding with the next screw. Repeat this process several times to ensure the plates are secured with equal force.

IMPORTANT NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

19

Image 19
Contents P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1 READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATIONOPERATOR’S MANUAL Two-Stage Snow ThrowerSafety Labels Table of ContentsFinding and Recording Model Number Customer SupportHEED ITS WARNING Your Responsibility Restrict the use Safety Labelsresult in personal injury. When you see this symbol in this manual and on the machinePractices Safe OperationTrainingPreparation Do not modify engine Maintenance & StorageSafe Operation Practices OperationSetting Up Your Snow Thrower instructions care adjustments to verifyPrior to operating Test on pageDrift Cutters If Equipped Tire Pressure Pneumatic Tires Clean-Out ToolClean-Out Tool Skid ShoesChoke Control Operating Your Snow ThrowerKnow Your Snow Thrower Shift LeverWheel Steering Controls Auger ControlDrive Control/ Auger Control Lock Four-Way Chute ControlStarting The Engine Gas & Oil Fill-UpStopping The Engine Electric Starter If EquippedAuger Control Test To Engage DriveTo Engage Augers Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlFigure 16A - Standard Skid Shoe Figure 16B - Reversible Skid Shoe Engine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesAuger Belt Replacement Always stop engine, disconnect spark Drive Belt Replacementof maintenance or adjustments on your machine AugersFriction Wheel Removal Off-Season Storage Remedy Trouble ShootingProblem CauseTWO YEAR SUPREME WARRANTY Description AUGER HOUSING COMPONENTS/COMPOSANTS DU LOGEMENT DES TARIÈRESWheel Assembly ModelPage PIÈCE PARTN DE DESCRIPTIONPage PIÈCE PARTN DE DESCRIPTIONPage DESCRIPTION 31A-6004 ANS DEUX DE SUPRÈME GARANTIE Problème SolutionDépannage CausesAVERTISSEMENT saison hors Remisageà carburant le Videz gaz 31 Figure d’entretien Régimefrottement de roue la de Démontage 32 Figure26 Figure transmission de courroie la de RemplacementTarières 28 Figure19 Figure la de courroie la de Remplacementtarière 23 Figureordinaire Patin - 18A Figure patins et plate Lame17 Figure réversible Patin - 16B Figure ordinaire Patin - 16A Figure 15 Figure Réglagestarière la de Commande Patinsvitesses de changement de Câble et transmission la de Commandegoulotte la de Commande vitesses de leviertarières les embrayer Pour souffleuse la de UtilisationAVERTISSEMENT tarière la de commande la de Testélectrique démarreur le d’utiliser d’huile et d’essence Pleinsmoteur du Arrêt modèles certains sur électrique Démarreurcontact de Clé échéant cas le tarières mission/des -trans de commande la de Blocageroues des d’orientation Commande échéant cas le poignéesà d’essence plein souffleuse la de Commandesdépart de Volet 11 Figurepneus des Pression montage de Instructionsgénéral d’ordre Recommandations goulotte la de dégagement de Outiléchéant cas le coupe de Barres montage de Instructions9 Figure 8 Figure 7 Figure de goupille la de Remisage cisaillement2 Figure 3 Figure1 Figure responsabilité Votre sécurité de ConsignesRemisage et Entretien SYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZPréparation sécuritéde Consignes Utilisationvous de avant arrêtées soient se sécurité de Étiquettesgoulotte la nettoyer pour dégagement de l’outil de servird’utilisation vente-après Servicemodèle de numéro le trouver Pour matières des Tableca.troybilt.www phases deux neige à SouffleuseD’UTILISATION NOTICE 4J1 N2G ONTARIO KITCHENER, 1386, Box .O .P