White Outdoor 769-04211 warranty Making Adjustments, Shift Cable, Chute Control

Page 12

5

Making

Adjustments

WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Never attempt to make any adjust- ments while the engine is running, except where speci- fied in operator’s manual.

Figure 5-1

Figure 5-2

Figure 5-3

Shift Cable

If the full range of speeds (forward and reverse) cannot be achieved, refer to the figure to the left and adjust the shift cable as follows:

1.Place the shift lever in the fastest forward speed position.

2.Loosen the hex nut on the shift cable index bracket. See Figure 5-1.

3.Pivot the bracket downward to take up slack in the cable.

4.Retighten the hex nut.

5.Check for correct adjustment before operating the snow thrower.

Chute Control

Once a season or every 25 hours of operation, whichever is earlier, check whether the four-way chute control™ cables have slackened. If the chute does not rotate fully, the chute control cables will have to be adjusted.

To adjust these cables, proceed as follows:

1.To tighten cable, loosen the top nut and tighten the bottom nut on the cable.

2.Adjust equally on both sides by working on both cables. See Figure 5-2.

Drive Control & Shift Lever

When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Check the adjustment of the drive control as follows:

1.With the drive control released, push the snow thrower gently forward. The unit should roll freely.

2.Engage the drive control and gently attempt to push the snow thrower forward. The wheels should not turn. The unit should not roll freely.

3.With the drive control released, move the shift lever back and forth between the R2 position and the F6 position several times. There should be no resistance in the shift lever.

4.If any of the above tests failed, the drive cable is in need of adjustment. Proceed as follows:

5.Loosen the lower hex nut on the drive cable bracket. See Figure 5-3.

6.Position the bracket upward to provide more slack (or downward to increase cable tension).

7.Retighten the lower hex nut.

WARNING: Run the engine com- pletely dry of gasoline before tipping snowthrower.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Two-Stage Snow Thrower 769-0421107/09/08 Table of Contents Finding and Recording Model NumberCustomer Support Safety Symbols There are rotating blades insideDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Clean-Out Tool Lamp Wiring Harness If equippedShear Pin Storage optional Drift Cutters If EquippedOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Starting the EngineStopping the Engine Engines with Starter Handle non-electric startTo Engage Drive To Engage AugersAuger Control Test Making Adjustments Shift CableChute Control Drive Control & Shift LeverYou can also check the adjustment as follows Space between the skid shoes and the ground can be adjustedTo adjust the skid shoes To adjust the auger control, refer toMaintaining Your Snow Thrower EngineLubrication AugersAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order To inspect the friction wheel, proceed as followsTrouble Shooting Problem Cause RemedyWarranty 05.28.08Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Optional/en option 42CPart RÉF Pièce Description 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Parts List Pièces Détachées For parts and/or accessories refer to customer support onAdressez-vous au «Service après-vente» La page 2 pour ce qui concerne les pièces et/ou accessoiresManual Chute Control Way Chute Control with tall chutePart RÉF Pièce Description Page Page Garantie SituationCom.mtdcanada Client du disposition la à exclusif recoursSolution Causes Problème DépannageRemisage de Instructions PropreSouffleuse Transmission de courroie la de Remplacement SouffleuseVis la REMARQUEréinstaller de PAS N’oubliez La de courroie la de Remplacement Patins et plate LameTarière TarièresRéglages Et transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleMoteur du Arrêt Moteur du marche en Mise ’huile et d’essence PleinsÉlectrique Faites NeFonctions 4 à goulotte la de Commande Roues des d’orientation CommandePhare Goulotte la de dégagement de OutilSouffleuse la de Commandes AmorçeurExplosif sont peurs Va les et inflammable La sur consignesPhare du câblage de Faisceau Pneus des PressionOption en cisaillement De goupille la de Remisage Échéant cas leCette Remarque Les RemarqueRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationVotre ’essence de ManipulationSécurité de Symboles Machine la d’utiliserVente-après Service Vente-après service au d’abord adresser vous sansModèle de numéro le trouver Pour Matières des TablePhases deux neige à Souffleuse 07/09/08 04211-769

769-04211 specifications

The White Outdoor 769-04211 is a noteworthy addition to the world of outdoor power equipment, designed for those who seek reliability and performance in their lawn care routine. This robust machine is primarily recognized as a walk-behind mower, showcasing features that cater to both homeowners and professional landscapers.

One of the standout characteristics of the 769-04211 is its powerful engine. Equipped with a high-performance motor, this mower ensures efficient cutting even in dense grass conditions. The engine delivers a reliable start and smooth operation, allowing users to tackle larger yards without the fear of stalling. The mower's cutting deck is designed to provide an optimal width, ensuring that users can cover more ground quickly while maintaining precision in their cuts.

The 769-04211 also boasts an adjustable cutting height feature, which allows users to customize the grass length to their preference. This feature is particularly beneficial for those who maintain different types of lawns, as it provides versatility to adapt to various grass species and seasonal growth patterns. With easily accessible height adjustment levers, transitioning between settings is straightforward, making the mowing process more efficient.

In terms of build quality, the White Outdoor 769-04211 emphasizes durability. Its chassis is constructed from robust materials designed to withstand the rigors of frequent use. This design consideration not only extends the life of the mower but also ensures consistent performance over time.

Another notable technology integrated into the 769-04211 is its mulching capability. This function allows grass clippings to be finely chopped and redistributed on the lawn, providing natural fertilization and promoting healthier growth. The option to switch between bagging and mulching adds to the mower's versatility, accommodating different user preferences and lawn conditions.

User comfort has not been overlooked in the design of the White Outdoor 769-04211. The mower features ergonomic handles that provide a secure grip, making it easier to maneuver around tight corners and obstacles. Additionally, its lightweight construction aids in reducing operator fatigue, ensuring that mowing does not become a strenuous task.

Overall, the White Outdoor 769-04211 stands out with its powerful engine, adjustable cutting height, durable construction, and user-friendly features. Whether for a small suburban yard or a larger landscape, this mower delivers reliability and efficiency, making it a valuable tool for anyone invested in maintaining their outdoor spaces.
Top Page Image Contents