White Outdoor 769-04211 You can also check the adjustment as follows, To adjust the skid shoes

Page 13

Figure 5-4 - Standard Skid Shoe

Figure 5-5 - Steel Reversible

Figure 5-6 - Plastic Reversible

5

Making

Adjustments

You can also check the adjustment as follows:

1.With the snow thrower tipped forward, remove the frame cover underneath the snow thrower by removing the self-tapping screws. See Figure 6-5 on page 15.

2.With the drive control released, there must be 1/8” clearance between the friction wheel and the drive pulley in all positions of the shift lever.

3.With the drive control engaged, the friction wheel must contact the drive pulley. See Figure 6-8.

4.If adjustment is necessary, loosen the lower hex nut on the drive cable index bracket and pivot the bracket upward or downward as necessary. Refer to Figure

5-3. Tighten the lower hex nut to secure the bracket when correct adjustment is reached.

5.Reassemble the frame cover and return the unit back to its operating position.

Skid Shoes

The space between the skid shoes and the ground can be adjusted.

•For close snow removal on a smooth surface, raise skid shoes higher on the auger housing.

•Use a middle or lower position when the area to be cleared is uneven, such as a gravel driveway.

To adjust the skid shoes:

1.Loosen the four hex nuts (two on each side) and carriage bolts. Move skid shoes to desired position.

2.Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes.

3.Retighten nuts and bolts securely.

NOTE: Some models are equipped with reversible skid shoes and may be turned over to increase their lifespan. See Figure 5-6 and 5-7.

IMPORTANT

It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on

Auger Control

To adjust the auger control, refer to page 11.

gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

13

Image 13

Contents 769-04211 Two-Stage Snow Thrower07/09/08 Finding and Recording Model Number Table of ContentsCustomer Support There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Lamp Wiring Harness If equipped Clean-Out ToolShear Pin Storage optional Drift Cutters If EquippedKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Starting the Engine Gas & Oil Fill-Up Stopping the Engine Engines with Starter Handle non-electric startTo Engage Augers To Engage DriveAuger Control Test Shift Cable Making AdjustmentsChute Control Drive Control & Shift LeverSpace between the skid shoes and the ground can be adjusted You can also check the adjustment as followsTo adjust the skid shoes To adjust the auger control, refer toEngine Maintaining Your Snow ThrowerLubrication AugersRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Friction Wheel Inspection Drive Belt ReplacementRemove and replace belt in the reverse order To inspect the friction wheel, proceed as followsProblem Cause Remedy Trouble Shooting05.28.08 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières 42C Optional/en optionPart RÉF Pièce Description Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 For parts and/or accessories refer to customer support on Parts List Pièces DétachéesAdressez-vous au «Service après-vente» La page 2 pour ce qui concerne les pièces et/ou accessoiresWay Chute Control with tall chute Manual Chute ControlPart RÉF Pièce Description Page Page Situation GarantieCom.mtdcanada Client du disposition la à exclusif recoursDépannage Solution Causes ProblèmePropre Remisage de InstructionsSouffleuse Souffleuse Transmission de courroie la de RemplacementVis la REMARQUEréinstaller de PAS N’oubliez Patins et plate Lame La de courroie la de RemplacementTarière TarièresRéglages Goulotte la de Commande Et transmission la de CommandeVitesses de levier Vitesses de changement de CâbleMoteur du Arrêt ’huile et d’essence Pleins Moteur du marche en MiseÉlectrique Faites NeRoues des d’orientation Commande Fonctions 4 à goulotte la de CommandePhare Goulotte la de dégagement de OutilAmorçeur Souffleuse la de CommandesExplosif sont peurs Va les et inflammable La sur consignesPneus des Pression Phare du câblage de FaisceauOption en cisaillement De goupille la de Remisage Échéant cas leLes Remarque Cette RemarqueResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre ’essence de ManipulationMachine la d’utiliser Sécurité de SymbolesVente-après service au d’abord adresser vous sans Vente-après ServiceModèle de numéro le trouver Pour Matières des Table07/09/08 04211-769 Phases deux neige à Souffleuse