White Outdoor 769-04211 warranty Drive Belt Replacement, Friction Wheel Inspection

Page 16

6

Maintaining

Your Snow

Thrower

NEVER replace the auger shear pins with standard hex pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

Drive Belt Replacement

WARNING: Run the engine com- pletely dry of gasoline before tipping snowthrower.

To remove and replace your snow thrower’s auger belt, proceed as follows:

1.Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 6-4.

2Carefully pivot the snow thrower up and forward so that it rests on the auger housing. See Figure 6-5.

3.Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it.

4.a. Roll the auger belt off the engine pulley.

b.Use a wrench to pivot the idler pulley toward the right. See Figure 6-9.

c.Lift the drive belt off engine pulley.

5.Back out the stop screw until the support bracket rests on the auger pulley. See Figure 6-10.

6.Slip the drive belt off the pulley and between friction wheel and drive plate. See Figure 6-10.

7.Remove and replace belt in the reverse order.

NOTE: Repeat the drive control adjustment on page 12 before operating the snowthrower.

Friction Wheel Inspection

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment fails to correct the problem, the friction wheel may need to be replaced.

NOTE: Special tools are required and several com- ponents must be removed and in order to replace the snow thrower’s friction wheel rubber. See an authorized Service Dealer to have the friction wheel rubber replaced or phone Customer Support as instructed on page 2 for information on ordering a Service Manual.

To inspect the friction wheel, proceed as follows:

1.Carefully pivot the snow thrower up and forward so that it rests on the auger housing. See Figure 6-5.

2.Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-5.

3.Examine the friction wheel for signs of wear or cracking. See Figure 6-11.

Off-Season Storage

If unit is to be stored over 30 days, prepare for storage as instructed in the separate engine manual packed with your snow thrower.

•Clean snow thrower thoroughly.

•Lubricate as instructed in the Maintenance section of this manual.

c a

b

Figure 6-9

Figure 6-10

Figure 6-11

•Refer to engine manual for correct engine storage instructions.

•Store the snow thrower in a clean, dry area.

•When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be taken to rustproof the equipment, especially springs, cables and all moving parts.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 769-04211 Two-Stage Snow Thrower07/09/08 Finding and Recording Model Number Table of ContentsCustomer Support Safety Symbols There are rotating blades insideDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Clean-Out Tool Lamp Wiring Harness If equippedShear Pin Storage optional Drift Cutters If EquippedOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Starting the EngineStopping the Engine Engines with Starter Handle non-electric startTo Engage Augers To Engage DriveAuger Control Test Making Adjustments Shift CableChute Control Drive Control & Shift LeverYou can also check the adjustment as follows Space between the skid shoes and the ground can be adjustedTo adjust the skid shoes To adjust the auger control, refer toMaintaining Your Snow Thrower EngineLubrication AugersRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order To inspect the friction wheel, proceed as followsTrouble Shooting Problem Cause RemedyWarranty 05.28.08Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Optional/en option 42CPart RÉF Pièce Description 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Parts List Pièces Détachées For parts and/or accessories refer to customer support onAdressez-vous au «Service après-vente» La page 2 pour ce qui concerne les pièces et/ou accessoiresManual Chute Control Way Chute Control with tall chutePart RÉF Pièce Description Page Page Garantie SituationCom.mtdcanada Client du disposition la à exclusif recoursSolution Causes Problème DépannagePropre Remisage de InstructionsSouffleuse Transmission de courroie la de Remplacement SouffleuseVis la REMARQUEréinstaller de PAS N’oubliez La de courroie la de Remplacement Patins et plate LameTarière TarièresRéglages Et transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleMoteur du Arrêt Moteur du marche en Mise ’huile et d’essence PleinsÉlectrique Faites NeFonctions 4 à goulotte la de Commande Roues des d’orientation CommandePhare Goulotte la de dégagement de OutilSouffleuse la de Commandes AmorçeurExplosif sont peurs Va les et inflammable La sur consignesPhare du câblage de Faisceau Pneus des PressionOption en cisaillement De goupille la de Remisage Échéant cas leCette Remarque Les RemarqueRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationVotre ’essence de ManipulationSécurité de Symboles Machine la d’utiliserVente-après Service Vente-après service au d’abord adresser vous sansModèle de numéro le trouver Pour Matières des TablePhases deux neige à Souffleuse 07/09/08 04211-769

769-04211 specifications

The White Outdoor 769-04211 is a noteworthy addition to the world of outdoor power equipment, designed for those who seek reliability and performance in their lawn care routine. This robust machine is primarily recognized as a walk-behind mower, showcasing features that cater to both homeowners and professional landscapers.

One of the standout characteristics of the 769-04211 is its powerful engine. Equipped with a high-performance motor, this mower ensures efficient cutting even in dense grass conditions. The engine delivers a reliable start and smooth operation, allowing users to tackle larger yards without the fear of stalling. The mower's cutting deck is designed to provide an optimal width, ensuring that users can cover more ground quickly while maintaining precision in their cuts.

The 769-04211 also boasts an adjustable cutting height feature, which allows users to customize the grass length to their preference. This feature is particularly beneficial for those who maintain different types of lawns, as it provides versatility to adapt to various grass species and seasonal growth patterns. With easily accessible height adjustment levers, transitioning between settings is straightforward, making the mowing process more efficient.

In terms of build quality, the White Outdoor 769-04211 emphasizes durability. Its chassis is constructed from robust materials designed to withstand the rigors of frequent use. This design consideration not only extends the life of the mower but also ensures consistent performance over time.

Another notable technology integrated into the 769-04211 is its mulching capability. This function allows grass clippings to be finely chopped and redistributed on the lawn, providing natural fertilization and promoting healthier growth. The option to switch between bagging and mulching adds to the mower's versatility, accommodating different user preferences and lawn conditions.

User comfort has not been overlooked in the design of the White Outdoor 769-04211. The mower features ergonomic handles that provide a secure grip, making it easier to maneuver around tight corners and obstacles. Additionally, its lightweight construction aids in reducing operator fatigue, ensuring that mowing does not become a strenuous task.

Overall, the White Outdoor 769-04211 stands out with its powerful engine, adjustable cutting height, durable construction, and user-friendly features. Whether for a small suburban yard or a larger landscape, this mower delivers reliability and efficiency, making it a valuable tool for anyone invested in maintaining their outdoor spaces.
Top Page Image Contents