White Outdoor 769-04211 Auger Belt Replacement, Unhook the support bracket spring from the frame

Page 15

Auger Belt Replacement

WARNING: Run the engine com- pletely dry of gasoline before tipping snowthrower.

To remove and replace your snow thrower’s auger belt, proceed as follows:

1.Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 6-4.

Figure 6-4

2.Carefully pivot the snow thrower up and forward so that it rests on the auger housing. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-5.

3.Roll the auger belt off the engine pulley. See Figure 6-6.

4.a. Loosen and remove the shoulder screw which acts as a belt keeper. See Figure 6-7.

b.Unhook the support bracket spring from the frame.

5.Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. Reassemble auger belt by following instructions in reverse order. See Figure 6-8.

NOTE: Repeat the auger control test on page 11 before operating the snowthrower.

NOTE: Do NOT forget to reinstall the shoulder screw and reconnect the spring to the frame after installing a replacement auger belt.

6

Maintaining

Your Snow

Thrower

NOTE: Although multi- viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils also result in higher oil consumption when used above 32ºF (0ºC). Check your snow thrower’s engine oil level more frequently to avoid possible engine damage from running low on oil.

Figure 6-7

Figure 6-5

IMPORTANT NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

Figure 6-6

Figure 6-8

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Two-Stage Snow Thrower 769-0421107/09/08 Table of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Drift Cutters If Equipped Clean-Out ToolLamp Wiring Harness If equipped Shear Pin Storage optionalKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Engines with Starter Handle non-electric start Gas & Oil Fill-UpStarting the Engine Stopping the EngineTo Engage Drive To Engage AugersAuger Control Test Drive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlTo adjust the auger control, refer to You can also check the adjustment as followsSpace between the skid shoes and the ground can be adjusted To adjust the skid shoesAugers Maintaining Your Snow ThrowerEngine LubricationAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame To inspect the friction wheel, proceed as follows Drive Belt ReplacementFriction Wheel Inspection Remove and replace belt in the reverse orderProblem Cause Remedy Trouble Shooting05.28.08 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières 42C Optional/en optionPart RÉF Pièce Description Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesFor parts and/or accessories refer to customer support on Adressez-vous au «Service après-vente»Way Chute Control with tall chute Manual Chute ControlPart RÉF Pièce Description Page Page Client du disposition la à exclusif recours GarantieSituation Com.mtdcanadaDépannage Solution Causes ProblèmeRemisage de Instructions PropreSouffleuse Souffleuse Transmission de courroie la de RemplacementVis la REMARQUEréinstaller de PAS N’oubliez Tarières La de courroie la de RemplacementPatins et plate Lame TarièreRéglages Vitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levierMoteur du Arrêt Faites Ne Moteur du marche en Mise’huile et d’essence Pleins ÉlectriqueGoulotte la de dégagement de Outil Fonctions 4 à goulotte la de CommandeRoues des d’orientation Commande PhareLa sur consignes Souffleuse la de CommandesAmorçeur Explosif sont peurs Va les et inflammableÉchéant cas le Phare du câblage de FaisceauPneus des Pression Option en cisaillement De goupille la de RemisageLes Remarque Cette RemarqueGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour07/09/08 04211-769 Phases deux neige à Souffleuse

769-04211 specifications

The White Outdoor 769-04211 is a noteworthy addition to the world of outdoor power equipment, designed for those who seek reliability and performance in their lawn care routine. This robust machine is primarily recognized as a walk-behind mower, showcasing features that cater to both homeowners and professional landscapers.

One of the standout characteristics of the 769-04211 is its powerful engine. Equipped with a high-performance motor, this mower ensures efficient cutting even in dense grass conditions. The engine delivers a reliable start and smooth operation, allowing users to tackle larger yards without the fear of stalling. The mower's cutting deck is designed to provide an optimal width, ensuring that users can cover more ground quickly while maintaining precision in their cuts.

The 769-04211 also boasts an adjustable cutting height feature, which allows users to customize the grass length to their preference. This feature is particularly beneficial for those who maintain different types of lawns, as it provides versatility to adapt to various grass species and seasonal growth patterns. With easily accessible height adjustment levers, transitioning between settings is straightforward, making the mowing process more efficient.

In terms of build quality, the White Outdoor 769-04211 emphasizes durability. Its chassis is constructed from robust materials designed to withstand the rigors of frequent use. This design consideration not only extends the life of the mower but also ensures consistent performance over time.

Another notable technology integrated into the 769-04211 is its mulching capability. This function allows grass clippings to be finely chopped and redistributed on the lawn, providing natural fertilization and promoting healthier growth. The option to switch between bagging and mulching adds to the mower's versatility, accommodating different user preferences and lawn conditions.

User comfort has not been overlooked in the design of the White Outdoor 769-04211. The mower features ergonomic handles that provide a secure grip, making it easier to maneuver around tight corners and obstacles. Additionally, its lightweight construction aids in reducing operator fatigue, ensuring that mowing does not become a strenuous task.

Overall, the White Outdoor 769-04211 stands out with its powerful engine, adjustable cutting height, durable construction, and user-friendly features. Whether for a small suburban yard or a larger landscape, this mower delivers reliability and efficiency, making it a valuable tool for anyone invested in maintaining their outdoor spaces.
Top Page Image Contents