White Outdoor 769-04211 warranty To Engage Drive, To Engage Augers, Auger Control Test

Page 11

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Do not shift speeds while the drive is engaged.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This drive lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Auger Control Test

Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower), engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the auger control in the disengaged “up” posi- tion, walk to the front of the machine.

Figure 4-2

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

7.To readjust the control cable, loosen the upper hex nut on the auger cable bracket. See Figure 4-2.

8.Position the bracket upward to provide more slack (or downward to increase cable tension).

9.Retighten the upper hex nut.

10.Repeat Auger Control Test to verify proper adjustment has been achieved.

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn 150°F (65°C). Do not touch.

When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower.

NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower

to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 07/09/08 Two-Stage Snow Thrower769-04211 Customer Support Table of ContentsFinding and Recording Model Number Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Drift Cutters If Equipped Clean-Out ToolLamp Wiring Harness If equipped Shear Pin Storage optionalKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Engines with Starter Handle non-electric start Gas & Oil Fill-UpStarting the Engine Stopping the EngineAuger Control Test To Engage DriveTo Engage Augers Drive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlTo adjust the auger control, refer to You can also check the adjustment as followsSpace between the skid shoes and the ground can be adjusted To adjust the skid shoesAugers Maintaining Your Snow ThrowerEngine LubricationUnhook the support bracket spring from the frame Auger Belt ReplacementRoll the auger belt off the engine pulley. See Figure To inspect the friction wheel, proceed as follows Drive Belt ReplacementFriction Wheel Inspection Remove and replace belt in the reverse orderProblem Cause Remedy Trouble Shooting05.28.08 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières 42C Optional/en optionPart RÉF Pièce Description Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesFor parts and/or accessories refer to customer support on Adressez-vous au «Service après-vente»Way Chute Control with tall chute Manual Chute ControlPart RÉF Pièce Description Page Page Client du disposition la à exclusif recours GarantieSituation Com.mtdcanadaDépannage Solution Causes ProblèmeSouffleuse Remisage de InstructionsPropre Souffleuse Transmission de courroie la de RemplacementVis la REMARQUEréinstaller de PAS N’oubliez Tarières La de courroie la de RemplacementPatins et plate Lame TarièreRéglages Vitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levierMoteur du Arrêt Faites Ne Moteur du marche en Mise’huile et d’essence Pleins ÉlectriqueGoulotte la de dégagement de Outil Fonctions 4 à goulotte la de CommandeRoues des d’orientation Commande PhareLa sur consignes Souffleuse la de CommandesAmorçeur Explosif sont peurs Va les et inflammableÉchéant cas le Phare du câblage de FaisceauPneus des Pression Option en cisaillement De goupille la de RemisageLes Remarque Cette RemarqueGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour07/09/08 04211-769 Phases deux neige à Souffleuse

769-04211 specifications

The White Outdoor 769-04211 is a noteworthy addition to the world of outdoor power equipment, designed for those who seek reliability and performance in their lawn care routine. This robust machine is primarily recognized as a walk-behind mower, showcasing features that cater to both homeowners and professional landscapers.

One of the standout characteristics of the 769-04211 is its powerful engine. Equipped with a high-performance motor, this mower ensures efficient cutting even in dense grass conditions. The engine delivers a reliable start and smooth operation, allowing users to tackle larger yards without the fear of stalling. The mower's cutting deck is designed to provide an optimal width, ensuring that users can cover more ground quickly while maintaining precision in their cuts.

The 769-04211 also boasts an adjustable cutting height feature, which allows users to customize the grass length to their preference. This feature is particularly beneficial for those who maintain different types of lawns, as it provides versatility to adapt to various grass species and seasonal growth patterns. With easily accessible height adjustment levers, transitioning between settings is straightforward, making the mowing process more efficient.

In terms of build quality, the White Outdoor 769-04211 emphasizes durability. Its chassis is constructed from robust materials designed to withstand the rigors of frequent use. This design consideration not only extends the life of the mower but also ensures consistent performance over time.

Another notable technology integrated into the 769-04211 is its mulching capability. This function allows grass clippings to be finely chopped and redistributed on the lawn, providing natural fertilization and promoting healthier growth. The option to switch between bagging and mulching adds to the mower's versatility, accommodating different user preferences and lawn conditions.

User comfort has not been overlooked in the design of the White Outdoor 769-04211. The mower features ergonomic handles that provide a secure grip, making it easier to maneuver around tight corners and obstacles. Additionally, its lightweight construction aids in reducing operator fatigue, ensuring that mowing does not become a strenuous task.

Overall, the White Outdoor 769-04211 stands out with its powerful engine, adjustable cutting height, durable construction, and user-friendly features. Whether for a small suburban yard or a larger landscape, this mower delivers reliability and efficiency, making it a valuable tool for anyone invested in maintaining their outdoor spaces.
Top Page Image Contents