Craftsman 247.88045 Throttle Control, Skid Shoes, Recoil Starter Handle, Electric Starter Button

Page 11

OPERATION

Throttle Control

The throttle control is located on the rear of the engine. It regulates the speed of the engine and will shut off the engine when moved into the STOP position.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces.

Recoil Starter Handle

This handle is used to manually start the engine.

Electric Starter Button

Pressing the electric starter button engages the engine’s electric starter when plugged into a 120V power source.

Electric Starter Outlet

Requires the use of a three-prong outdoor extension cord (included) and a 120V power source/wall outlet.

Augers

When engaged, the augers rotate and draw snow into the auger housing.

Chute Assembly

Snow drawn into the auger housing is discharged out the chute assembly.

Drive Control/ Auger Control Lock

DRIVE

CONTROL

GO

The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release to stop.

The drive control also locks the auger control so you can operate the chute directional control without interrupting the snow throwing process. If the auger control is engaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release both controls to stop the augers and wheel drive.

NOTE: Always release the drive control before changing speeds. Failure to do so will result in increased wear on your machine’s drive system.

Two-way chute Control™

The distance snow is thrown can be changed by adjusting the angle of the chute assembly. Move the chute control forward to decrease the distance, toward the rear to increase.

Gas Cap

Unthread the gas cap to add gasoline to the fuel tank.

Auger Control

AUGER

CONTROL

GO

The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop.

Chute Directional Control

The chute directional control is located on the left side of the snow thrower.

•To change the direction in which snow is thrown, crank clockwise to discharge to the left and counterclockwise to discharge to the right.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles. Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

Headlight

The headlight is located on top of the handle panel. It may be adjusted by loosening the screws on each side of the light housing, pivoting the light up or down, and retightening the screws.

Drift cutters

The drift cutters are designed for use in deep snow. Their use is optional for normal snow conditions.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 28/2007 Form noProduct Specifications Model Number Table of ContentsWarranty Statement Preparation Safety InstructionsTraining Operation Maintenance & StorageUSE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsPlace the shift lever in the F6 position AssemblyAssembly Removing From CrateDrift Cutters Chute Clean-Out ToolSet-Up Control AdjustmentsTire Pressure Skid ShoesRetighten nuts and bolts securely Testing Auger Drive ControlTesting Drive Control & Shift Lever Adjusting Drive and Auger ControlsOperation Recoil Starter Handle Chute AssemblyThrottle Control Skid ShoesStarting The Engine Clean-Out ToolBefore Starting Engine To Engage Augers Replacing Shear PinsStopping The Engine To Engage DriveOil FIll Oil Drain Service and MaintenanceChecking Engine Oil Changing Engine OilLubrication Chute Control Shave Plate and Skid ShoesShave Plate Shift RodAuger Control Belt replacementDrive Control Chute BracketLoosen the bolt shown in securing the belt keeper Auger Belt ReplacementHousing forward and pulling up the handles If also replacing the drive belt, proceed to the Drive Belt Drive Belt ReplacementBelleville Washer Slide Hex Shaft Out Right Side Changing Friction WheelEach Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesShort-Term Storage OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTroubleshooting Craftsman Snow Thrower Model Parts List39 -04020 Spacer, 1.004 x 1.375 x 721-0146 Housing, Auger 684-04151Parts List 77 -1658 Lamp 725-1669 41 -0963 Connector, Shift Rod79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet 61 -0199A Bumper, Rubber 784-5619B79 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer 37083 Cylinder Incl , 20, 72Dowel Pin Oil Drain Extension Not Available35691 Governor Link 35079A Key Switch Bracket Incl a28425 37085 Intake PipeMarked 351 32180C Primer Line 355Packaged 740053B 400 36947BPage This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Repair Protection Agreement Número DE Modelo ÍndiceDeclaración DE Garantía Especificaciones DEL ProductoPreparativos Instrucciones DE SeguridadCapacitación Mantenimiento y almacenamiento OperaciónMontaje Coloque la palanca de cambios en posición F6Montaje Extracción de la unidad del cajónCortadores de desplazamiento de nieve ConfiguraciónHerramienta de limpieza del canal Zapatas antideslizantes AjustesPresión de los neumáticos Vea Ajuste de transmisión y controles de barrena Prueba de control de transmisión y palanca de cambiosPrueba del control de la transmisión de la barrena Faro Palanca de cambiosOperación Llave de encendidoSalida del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Botón del arrancador eléctricoAntes de encender el motor Control del canal de 2 direccionesControl direccional del canal Herramienta de limpiezaArrancador de retroceso Detención del motorProcedimiento para engranar la transmisión Procedimiento para engranar las barrenasCambio de aceite del motor Servicio Y MantenimientoMantenimiento de Motor Control del aceite del motorLubricación Control del canal Placa de raspado y zapatas antideslizantesPlaca de raspado Varilla de cambioControl de la barrena Cambio de correaControl de la transmisión Soporte del canalHolgazán de taladro es mantenida Reemplazo de la correa de la barrenaDel motor. Vea la Figura Nota Asegúrese que la posición del regatón en la vara deRanura de polea Adaptador Reemplazo de la correa de transmisiónBarrena al eje de entrada Motor e instale nuevamente la cubierta de la correaEje hexagonal Cambio de la rueda de fricciónDeslice el separador sobre el extremo del eje hexagonal Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarAlmacenaje a Corto plazo Almacenamiento Fuera DE TemporadaPreparación del motor Preparación de la máquina quitanieveSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents